如果网络管理员在交换机上输入以下命令,会有什么结果?Switch1(config-line)# line console 0 Switch1(config-line)# password cisco Switch1(config-line)# login ()
What is the importance of using Virtual Output Queues on ingress Line Cards in a high-end router?()
路由器命令“Router(config)#access-listldeny192.168.1.1”的含义是()。
在配EIGRP的时候(frame-relay的NBMA)命令router(config-router)#neighbor 192.168.1.129 是什么意思呢?
Router# show interfaces serial 0/1 命令的输出显示了如下内容: Serial0/1 is down, line protocol is down. 线路协议为 down(关闭)的原因最可能是什么()
Why is the Cisco Integrated Services Router product line A good choice for customers?()
请问以下配置中,R1的OSPF路由器ID是什么() R1(config)#interface s0/0/0 R1(config-if)#ip add 192.168.2.1 255.255.255.252 R1(config)#int loopback 0 R1(config-if)# ip add 10.1.1.1 255.255.255.255 R1(config)#router ospf 1 R1(config-if)#network 192.168.2.0 0.0.3.255 area 0
路由器命令“Router(config)#access-list 1 permit192.168.1.1”的含义是()。
A Cisco router has been configured, and the copy running-config startup-config command has been issued. When the router is power cycled, the router prompts with: "Would you like to enter the initial configuration dialog? [yes/no]" Why has this occurred?()
What s the default stratum clock on a Cisco router,when you see the key word "master" configured on the NTP line?()
The TestKingA router is configured as shown below: TestKingA(config)# interface loopback 0 TestKingA(config-if)# ip address 192.168.16.24 255.255.255.255 As a result of this change, which of the statements below are true?()
网络管理员正在尝试添加一个新的路由器成为一个既定的OSPF网络。附连到新的路由器的网络不出现在其他OSPF路由器的路由表。考虑到如下图所示的部分配置信息,什么样的配置错误导致这个问题?() Router(config)#router ospf 1 Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
如果Cisco路由器有如下SNMP的配置: Router(config)#snnip-serverenabletraps Router(config)#sump-serverhostadmin.tjut.edu.cnadmin 那么,下列描述中错误的是()。
路由器命令配置中有不同的模式,请将下列路由器工作模式的转换补充完整。Router>Router#Router(config)# f0/0Router(config-if)#Router(config)#Router(config-router)#endRouter#
路由器命令“Router(config) access-list 10 permit 192.168.1.1”的含义是()()
【单选题】当使用下列命令配置了路由器后,将有多少地址可用于进行动态NAT转换? router(config)ip nat pool TAME 209.165.201.23 209.165.201.30 netmask 255.255.255.224 router(config)ip nat inside source list 9 pool TAME
◑路由器“全局模式”的提示符为()◑A.>◑B.◑C.(config)◑D.(config-router)
两台路由器RTA、RTB的串口S0用一条链路连接,链路协议位PPP,两各接口的网络类型均为point-to-point,此时接口与链路均为UP,配置该网段:RTA(config-if-serial0)ipaddress 10.10.10.1 255.255.0.0;RTA(config-router-ospf)network 10.10.10.10.0.0.0area 1;RTB(config
进入接口配置模式,使用bandwidth命令设置接口带宽。Router(config-if) bandwidth2500000表示设置
After making changes to the router, you issue the "copy running-config startup-config" command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode.What is the most likely cause of this?()
路由器命令“Router(config)access-list1permit192.168.1.1”的含义是允许()的分组通过,如果分组不匹配,则检查下一条语句。
根据网络拓扑和需求说明,完成(或解释)路由器R1的配置。 Router(config) ipv6 unicast-routing(3)
17、在配置路由器时,网络技术人员发出以下命令: Ra(config)router ospf 1 Ra(config-router)network 10.10.10.0 0.0.0.255 area 0 数字1代表什么?
在路由器上输入了下列命令: Router(config) access-list 2 deny 172.16.5.24 Router(config) access-list 2 permit any ACL 已正确应用至接口。通过该组命令,可得出什么结论?