Which command series should be used to determine whether file paging or paging space paging is a problem when running a program from an idle system？（）

A .  both active and passive modes FTP are supported B .  by default the FTP proxy uses port 8021 C .  access polices may apply to native FTP traffic D .  data loss prevention policies may apply to native FTP traffic E .  authentication is supported in transparent mode

A . Voltage B . Current C . Resistance D . Inductance

A . QuickVPN (QVPN) client software for simplified management B . minimal configuration requirements C . 802.1g capabilities and support for multiple wireless networks simultaneously (multiple BSSIDs) D . wireless bridging to overcome the lack of physical network cable

A . 1812 B . 1814 C . 1802 D . 1811 E . 1841

A .  a customer with CIFS, NFS and GPFS requirements  B .  a customer wanting to natively implement Easy Tier  C .  a customer who has large block sequential write requirements  D .  a customer who needs to consolidate multiple storage controllers under one managementinterface&e

A .  Smart Business Suite B .  VoiceView Express C .  TimeCard View D .  Cisco Unified CallConnector E .  Cisco WebEx PhoneConnect F .  Connected Data Protector

A .  independent of SSO B .  NSF combined with SSO enables supervisor engine load balancing C .  supported by RIPv2， OSPF， IS-IS， and EIGRP D .  supports IPv4 and IPv6 multicast E .  prevents route flapping F .  dependent on FIB table

A .  The bring up protocol automatically detects and overrides any misconfiguration. B .  You can manually configure channel groups， or they can be automatically created. C .  Changes in configuration to the SAN port channel interface must also be made to all members of the channel group. D .  The port channel protocol uses the exchange fabric parameters command to communicate across peer ports in an ISL. E .  The port channel protocol ensures that a set of ports is eligible to be part of the same SAN port channel.

A . R1（config）# interface ethernet 0；R1（config-if）# ip address 192.1.1.129 255.255.255.192；R1（config-if）# no shutdown B . R1（config）# interface ethernet 0；R1（config-if）# ip address 192.1.1.97 255.255.255.192；R1（config-if）# no shutdown C . R1（config）# interface serial 0；R1（config-if）# ip address 192.1.1.4 255.255.255.252；R1（config-if）# clock rate 56000 D . R1（config）# interface serial 0；R1（config-if）# ip address 192.1.1.6 255.255.255.252；R1（config-if）# no shutdown E . R1（config）# router rip；R1（config-router）# network 192.1.1.4；R1（config-router）# network 192.1.1.128 F . R1（config）# router rip；R1（config-router）# version 2；R1（config-router）# network 192.1.1.0

A . ssh B . connect C . login D . sessio

A . It is used to restart the router. B . It is used to bypass the configuration in NVRAM. C . It is used to enter ROM Monitor mode. D . It is used to view the lost password. E . It is used to save the changes to the configuration.

A .  passive optical network （PON） B .  serial C .  Fibre Channel D .  Fast Ethernet E .  ADSL2+

A . reset of the primary supervisor B . manual switchover from standby to active supervisor C . manual switchover from active to standby supervisor D . automatic switchover from active to standby on primary supervisor failure

A .  M-Series appliance B .  sawmill for CiscoIronPort C .  the built-in WSA reporting infrastructure D .  Cisco application control engine

A .  Cisco 1130AG Series Wireless LAN Controllers B .  Cisco 1140AG Series Wireless LAN Controllers C .  Cisco 2000 Series Wireless LAN Controllers D .  Cisco 4400 Series Wireless LAN Controller

A .  Enable conversational learning on FabricPath vlans 1-10 for F-Series module B .  Enable FabricPath protocol on VLANs 1–10 C .  No need for this command as conversational learning is enabled by default for all VLANs. D .  Enable conversational learning on Classical Ethernet VLAN for F-Series module

A .  A single SAN port channel can have both Fibre Channel and virtual Fibre Channel interfaces.  B .  SAN port channels can include up to 16 interfaces. C .  SAN port channels distribute traffic across all links in the port channel when source ID and destination ID load balancing are used. D .  The links in SAN port channels can be connected to different sets of switches. E .  The On mode of operation means ports only operate as part of a SAN port channel or remain inactive.

A . Integrated Hardware for offload of encryption services B . Wireless LAN C . SRST with centralized Cisco CallManager fro up to 120 IP Phones D . Support For up to Eight NMEs E . Cisco CallManager Express for up to 36 IP Phones support F . High Performance Architecture optimized for concurrent service deployment

A . independent of SSO B . NSF combined with SSO enables supervisor engine load balancing C . supported by RIPv2， OSPF， IS-IS， and EIGRP D . supports IPv4 and IPv6 multicast E . prevents route flapping F . dependent on FIB table

A .  A single VACL can be shared across two or more VDCs. B .  Use of VACLs requires no special license to be installed. C .  VACLs make use of IP or MAC ACLs. D .  Only options drop and forward are permitted.

A .  The supervisor module enforces CoPP before out-of-policy traffic reaches the CPU B .  The fabric modules enforce CoPP in the fabric before out-of-policy traffic reaches the CPU  C .  The linecards enforce CoPP locally before out-of-policy traffic reaches the CPU D .  The egress virtual output queue enforces CoPP locally before out-of-policy traffic reaches the CPU

A . disables OIR on the VAM2+ module B . removes the VAM2+ crypto engine feature and disables the associated configuration commands from the router C . disables dual VAM2+ hardware stateful failover capabilities D . disables the crypto engine hardware acceleration, resulting in all crypto functions to be performed in software

A．A.nprotection clock B．B.nforced switching C．C.nmanual switching D．D.nclear

A．A.steering B．B.wrapping C．C.1+1 LSP D．D.1:1 LSP