What are the purposes of accounting（）

A . To allow HTTP access to the WLAN controller B . To allow SSH access to the CLI of the WLAN controller C . To allow SSL access to the CLI of the WLAN controller D . To allow HTTPS access to the WLAN controller E . None of the other alternatives apply

A . It ensures that data is retransmitted if an acknowledgment is not received. B . It reassembles segments in the correct order on the destination device. C . It provides a mechanism for the receiver to control the transmission speed. D . It regulates the size of each datagram segment. E . All of the above are functions of flow control

A . To experiment with shared processor pools B . To isolate physical hardware between workloads C . To control resource utilization on an application-by-application basis D . To leverage Workload Partition Manager for performance trending and analysi

A . To experiment with shared processor pools B . To isolate physical hardware between workloads C . To control resource utilization on an application-by-application basis D . To leverage Workload Partition Manager for performance trending and analysi

A . VLANs logically divide a switch into multiple, independent switches at Layer 2. B . Trunk links can carry traffic for multiple VLANs. C . VLAN implementation significantly increases traffic due to added trunking information. D . A VLAN can span multiple switches. E . VLANs typically increase the number of switches needed F . VLANs typically decrease the number of switches needed

A . acts as a meeting place for sources and receivers of multicast traffic B . used in PIM dense m ode to create a database of all multicast sources C . used in PIM dense and sparse mode to create a database of all multicast sources D . acts as the designated router for a broadcast segment when multicast routing is enabled

A . The source database backup must be copied over the net for test database. B . The source database must be run in ARCHIVELOG mode if the database is open. C . The source database must be shut down cleanly if the database is in mounted state. D . A net service name should be set up and a listener configured with the target as well as the source database.

A . It is used with the OSPF priority values to determine which OSPF router will become the DR or BOR in a point-to-point network B . It is used with the OSPF priority values to determine which interface will be used to form a neighbor relationship with another OSPF router C . It is used with the OSPF priority values to determine which router will become the DR or BOR in a multi access network D . It is used to determine which interfaces will send Hello packets to neighboring OSPF router

A . It is used to restart the router. B . It is used to bypass the configuration in NVRAM. C . It is used to enter ROM Monitor mode. D . It is used to view the lost password. E . It is used to save the changes to the configuration.

A . it is not used in multicast B . it determines the virtual address group for a multicast destination C . it dynamically registers individual hosts in a multicast group on a specific LAN D . it is used on WAN connections to determine the maximum bandwidth of a connection E . it determines whether Bidirectional PIM or PIM sparse mode will be used for a multicast flow

A . to support PUSH-based active database duplication B . to support synchronization of a standby database with the primary database in a Data environment C . To support PULL-based active database duplication D . To support file restores over the network in a Data Guard environment E . To support file recovery over the network in a Data Guard environment

A . It allows for rotation of the hook in the single mode B . It is required to“twin-up”30-ton pedestal cranes C . It is used to pick up light loads D . It is used to rigidly connect two crane

A .  it is not used in multicast B .  it determines the virtual address group for a multicast destination C .  it dynamically registers individual hosts in a multicast group on a specific LAN D .  it is used on WAN connections to determine the maximum bandwidth of a connection E .  it determines whether Bidirectional PIM or PIM sparse mode will be used for a multicast flow

A . Provides surface for applying force on machinery B . Provides landing surface for the sounding bob C . Absorbs machinery vibration D . Prevents valve stem over-travel

A .  The ObjectFactory class is the generated Service Endpoint Interface class B .  The ObjectFactory class is the generated service provider class that is used by the JAX-WS client. C .  The ObjectFactory class takes the targetNamespace value and creates the directory structure. D .  The ObjectFactory class allows you to programatically construct new instances of the Java representation for XML content.

A . present Cisco products B . provide a framework of tested and proven models C . identify basic needs of the business D . calculate the business need priority

A . Provides local hosts with a default gateway address B . Allows remote management of the switch. C . Allows the switch to respond to ARP requests between two hosts D . Ensures that hosts on the same LAN can communicate with each other.

A:2; B:3; C:4; D:5