-
Which command shows your active Telnet connections?()
A . show session
B . show cdp neighbors
C . show users
D . show queue
-
Which line from the output of the show ip interface command indicates a layer 1 problem?()
A . Serial0/1 is up, line protocol is down
B . Serial0/1 is down, line protocol is down
C . Serial0/1 is up, line protocol is up
D . Serial0/1 is administratively down, line protocol is dow
-
Which command encrypts all plaintext passwords?()
A . Router(config)#password-encryption
B . Router(config)#service password-encryption
C . Router#service password-encryption
D . Router# password-encryptio
-
You issued the RMAN>SHOW ALL; command. The output of this command is as follows:
https://assets.asklib.com/images/image2/2018080116074760626.jpg
After analyzing the output, which conclusion will you draw?()
A . The current control file is not automatically backed up every time you perform a backup.
B . The backups save space on the storage media.
C . While performing backups across a network, the network bandwidth is reduced.
D . The backups consist of backup pieces.
-
Which statement best describes what is depicted in the show command output?()
A . IGMP snooping is not active for VLAN 120 because the IGMP feature has not been enabled on the switch with the feature igmp command.
B . The IGMP snooping querier for VLAN 120 is not in a running state because the Loopback interface configured with 1.1.1.1/32 is currently in a down state.
C . IGMP snooping has been disabled on the VLAN 120 SVI.
D . IGMP snooping has been disabled for VLAN 120 in VLAN configuration mode.
E . IGMP snooping is not active for VLAN 120 because VLAN 120 does not exist in the VLAN database.
-
Which command shows system hardware and software version information?()
A . show configuration
B . show environment
C . show inventory
D . show platform
E . show versio
-
Which command will list all subsystem resources on a server?()
A . lssrc a
B . lssrc g
C . lssrc l
D . lssrc -
-
The man page for command shows the following syntax: The man page for command shows the following syntax: command [ -a -b ] Which of the following statements is true regarding this entry?()
A . Either the -a or flag -b may be used, but not both.
B . If the flag -a is used then the flag -b also must be used.
C . One of the -a or -b flags must be used, but not both at the same time.
D . Both the flags may be used together, but neither are mandatory.
-
Which command shows if an access list is assigned to an interface?()
A . show ip interface [interface] access-lists
B . show ip access-lists interface [interface]
C . show ip interface [interface]
D . show ip access-lists [interface]
-
Which command will list all subsystem resources on a server?()
A . lssrc a
B . lssrc g
C . lssrc l
D . lssrc -
-
After executing the "show host" command, which of the information below would you see?()
A . The IP addresses of workstations allowed gain access to the router via an access list
B . Permanent name-to-address mappings created using the ip host command.
C . Temporary and permanent DNS entries.
D . The names of the routers created using the hostname command.
E . The length of time of users logged into the router, as well as the duratio
-
Which command will show the network configuration settings associated with an Ethernet adapter?()
A . lscfg
B . lsdev
C . netstat
D . ifconfig
-
A network design shows that R1 has four different possible paths from itself to the Data Center subnets. Which one of the following commands is most likely to show you all the possible next - hop IP addresses for these four possible routes?()
A . show ip eigrp topology
B . show ip eigrp topology all - links
C . show ip route eigrp
D . show ip route eigrp all - links
E . show ip eigrp topology all - learned
-
Which command shows all the paging spaces available on a system?()
A . lsps -a
B . showps -a
C . psdisplay -l
D . swaplist -ALL
-
Which command shows if an access list is assigned to an interface?()
A . show ip interface [interface] access-lists
B . show ip access-lists interface [interface]
C . show ip interface [interface]
D . show ip access-lists [interface]
-
Which command will show the MAC addresses of stations connected to switch ports?()
A . show mac-address
B . show arp
C . show table
D . show switchport
-
Which show command will display only the Type 5 LSAs in the OSPF topology database?()
A . show ip ospf database external
B . show ip ospf database nssa - external
C . show ip route ospf
D . show ip ospf datab ase summary
E . show ip route
-
Which of the following commands should be used to show DNS information?()
A . trace
B . netstat
C . ifconfig
D . nslooku
-
Which command shows dump components and controls live dump attributes?()
A . dumpctrl
B . sysdumpdev
C . livedumpdev
D . livedumpctrl
-
Which command shows your active Telnet connections?()
A . show session
B . show cdp neighbors
C . show users
D . show queue
-
Which IOS command shows the detailed error report?()
A . errpt -A
B . errpt -a
C . errlog -a
D . errlog -l
-
Router R1 lists 4 routes for subnet 10.1.1.0/24 in the output of the show ip eigrp topology all - links command. The variance 200 command is configured, but no other related commands are configured. Which of the following rules are true regarding R1‘s decision of what r outes to add to the IP routing table?Note that RD refers to reported distance and FD to feasible distanc E.()
A. Adds all routes for which the metric is <= 200 * the best metric among all routes
B. Adds all routes because of the ridiculously high variance setting
C. Adds all successor and feasible successor routes
D. Adds all successor and feasible successor routes for which the metric is<=200 * the best metric among all routes
-
A network design shows that R1 has four different possible paths from itself to the Data Center subnets.Which one of the following commands is most likely to show you all the possible next - hop IP addresses for these four possible routes?()
A. show ip eigrp topology
B. show ip eigrp topology all - links
C. show ip route eigrp
D. show ip route eigrp all - links
E. show ip eigrp topology all - learned
-
On PTN devices, command show interface all can be executed to detect status of all int
是
否