Refer to the exhibit. R1 and R2 have been configured to share routing information via EIGRP. What will be the result of the configuration section shown for R2? （）https://assets.asklib.com/images/image2/2018073108583876318.png
A . Any routes learned by R2 from the interface tied to the 172.16.0.0 network will not be advertised to neighbors on the 192.168.2.0 network.
B . Only routes learned by R2 from the interface tied to the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network.
C . Only the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network.
D . All networks, except the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network .
-
Refer to the exhibit. The output that is shown is generated at a switch. Which three of these statements are true? （）
A . All ports will be in a state of discarding, learning, or forwarding.
B . Thirty VLANs have been configured on this switch.
C . The bridge priority is lower than the default value for spanning tree.
D . All interfaces that are shown are on shared media.
E . All designated ports are in a forwarding state.
F . The switch must be the root bridge for all VLANs on this switch.
-
Refer to the exhibit. In this network， R1 is configured not to perform autosummarization within EIGRP. What routes will R3 learn from R2 through EIGRP？ （）https://assets.asklib.com/images/image2/2018072318005941808.jpg
A . 172.30.1.0/24 and 10.1.2.0/24；EIGRP only performs autosummarization at the edge between two major networks.
B . 172.30.0.0/16 and 10.1.2.0/24；R2 will perform autosummarization although R1 will not.
C . Since R2 is configured without autosummarization， it will not propagate the 172.30.1.0/24 route.
D . 172.30.0.0/8 and 10.0.0.0/8.
-
Refer to the exhibit. The company uses EIGRP as the routing protocol. What path will packets take from a host on 192.168.10.192/26 network to a host on the LAN attached to router R1?（）https://assets.asklib.com/images/image2/2018072410123247953.jpg
A . The path of the packets will be R3 to R2 to R1.
B . The path of the packets will be R3 to R1 to R2.
C . The path of the packets will be both R3 to R2 to R1 and R3 to R1.
D . The path of the packets will be R3 to R1
-
Refer to the exhibit. Router R1 is being used as a relay device for autoconfiguration of switch S1.Which configuration will acc omplish this? （）https://assets.asklib.com/images/image2/2018073015150790983.jpg
A . S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 10.0.0.2
B . S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 20.0.0.1
C . R1(config)# interface fastethernet 0/0 R1(config - if)# ip help er - address 20.0.0.2R 1(config - if)# ip helper - address 20.0.0.3 R1(config - if)# ip helper - address 20.0.0.4 R1(config - if)# exit R1(config)# interface fastethernet 0/1 R1(config - if)# ip helper - address 10.0.0.1
D . R1(config)# interface fastethernet 0/0 R1 (config - if)# ip helper - address 20.0.0.1 R2(config)# interface fastethernet 0/0 R2(config - if)# ip helper - address 20.0.0.1 R3(config)# interface fastethernet 0/0 R3(config - if)# ip helper - address 20.0.0.1 R4(config)# interface fastethernet 0/0 R4(config - if)# ip helper - address 20.0.0.1
E . S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 10.0.0.2 R2(config)# interface fastethernet 0/0 R2(config - if)# ip helper - address 20.0.0.1 R3(config)# interface fastethernet 0/0 R3(config - if) # ip helper - address 20.0.0.1 R4(config)# interface fastethernet 0/0 R4(config - if)# ip helper - address 20.0.0.1
-
Refer to the exhibit. GLBP has been configured on the network. When the interface serial0/0/1 on router R1 goes down，
how is the traffic coming from Host1 handled？ （）
https://assets.asklib.com/images/image2/2018073015230243383.jpg
A . The traffic coming from Host2 is forwarded through router R2 with no disruption. The traffic from Host1 is dropped due to the disruption of the load balancing feature configured for the glbp group.
B . The traffic coming from both hosts is temporarily interrupted while the switchover to make R2 active occurs.
C . The traffic coming from Host2 is forwarded through router R2 with no disruption. Host1 sendsan ARP request to resolve the MAC address for the new virtual gateway.
D . The traffic coming from Host1 and Host2 is forwarded through router R2 with no disruption.
-
Refer to the exhibit. In this network， R1 is configured not to perform autosummarization within EIGRP. What routes will R3 learn from R2 through EIGRP？（）https://assets.asklib.com/images/image2/2018072317583328155.jpg
A . 172.30.1.0/24 and 10.1.2.0/24； EIGRP only performs autosummarization at the edge between two major networks.
B . 172.30.0.0/16 and 10.1.2.0/24； R2 will perform autosummarization， although R1 will not.
C . Since R2 is configured without autosummarization， it will not propagate the 172.30.1.0/24 route.
D . 172.30.0.0/8 and 10.0.0.0/8.
-
Refer to the exhibit.
Which protocol establishes an optimal path to the root in a wireless mesh network？ （）
https://assets.asklib.com/images/image2/2018073011454335678.jpg
A . Adaptive Wireless Path （AWP）
B . WLAN Quality of Service （WQoS）
C . Lightweight Access Point Protocol （LWAPP）
D . 802.1Q WLAN trunking protocol
E . Layer 2 Roaming （IAPP）
-
Refer to the exhibit. What statement is true about the interface S1/0 on router R1？（）https://assets.asklib.com/images/image2/2018072411394669613.jpg
A . Labeled packets can be sent over an interface.
B . MPLS Layer 2 negotiations have occurred.
C . IP label switching has been disabled on this interface.
D . None of the MPLS protocols have been configured on the interface.
-
Refer to the exhibit.Which is the most efficient summarization that R1 can use to advertise its networks toR2？（）https://assets.asklib.com/images/image2/2018072314093859691.jpg
A . 172.1.4.0/22
B . 172.1.0.0/21
C . 172.1.0.0/22
D . 172.1.4.0/25 172.1.4.128/25 172.1.5.0/24 172.1.6.0/24 172.1.7.0/24
E . 172.1.4.0/24 172.1.5.0/24 172.1.6.0/24 172.1.7.0/24
-
Refer to the exhibit. Routers R1 and R2 are running EIGRP and have converged. On the basis of the information that is presented, which statement is true? （）https://assets.asklib.com/images/image2/2018073011042561240.jpg
A . Both outgoing and incoming routing updates on R1 will be permitted because the d istribute - list 20 out Serial0/0 command cannot be used with association with the outgoing interface.
B . All incoming routing updates from R2 will be suppressed, but the outgoing updates will continue to be sent.
C . Both outgoing and incoming routing up dates on R1 will be stopped because of the passive - interface Serial0/0 configuration statement.
D . All outgoing routing updates from router R1 to router R2 will be suppressed, but the inbound updates will continue to be received.
-
Refer to the exhibit.
https://assets.asklib.com/images/image2/201807301615135089.png
Which order correctly identifies the steps to provision a cable modem to connect to a headend as defined by the DOCSIS standard？（）
A . A→D→C→G→E→F→B
B . A→D→E→G→C→F→B
C . C→D→F→G→E→A→B
D . C→D→F→G→A→E→B
E . F→D→C→G→A→E→B
-
Refer to the exhibit.Based on the exhibited routing table，how will packets from a host within the192.168.10.192/26 LAN be forwarded to 192.168.10.1？（）https://assets.asklib.com/images/image2/2018072314090474779.jpg
A . The router will forward packets from R3 to R2 to R1
B . The router will forward packets from R3 to R1
C . The router will forward packets from R3 to R1 to R2
D . The router will forward packets from R3 to R2 to R1 AND from R3 to R1
-
Refer to the exhibit. OSPF is configured on all routers in the network. On the basis of the show ip ospf n eighbor output, what prevents R1 from establishing a full adjacency with R2? （）https://assets.asklib.com/images/image2/2018073015404016990.jpg
A . Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.
B . Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.
C . Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.
D . Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.
E . The Hello parameters on routers R1 and R2 do not m atch.
-
Refer to the exhibit,a network administrator cannot establish a telnet session with the indicated router.What is the cause of this failure?（）
A . A level 5 password is not set
B . The vty password is missing
C . The console password is missing
D . An ACL is blocking Telnet acce
-
Refer to the exhibit. The DHCP configuration that is shown is configured on a Cisco router. Whichstatement is true？（）
A . The router will distribute IP addresses from pool 1 until its addresses are exhausted. Then therouter will begin distributing addresses from pool 2
B . The configuration is invalid because the DHCP options are global configuration commands
C . The configuration is incomplete until the DHCP pools are bound to the appropriate interface orinterfaces
D . The router will choose which pool to use based upon the interface the DHCP request wasreceived o
-
Refer to the exhibit. Router R1 is connected to networks 172.1 6.1.0 /26 and 172.16.1.64 /27. On the basis of the partial output in the exhibit, which statement is true? （）https://assets.asklib.com/images/image2/2018073010540810068.jpg
A . Router R1 will deny the 172.16.1.0/26 route while permitting the 172.16.1.64/27 route to be advertised.
B . Router R1 will advertise both rou tes.
C . Router R1 should be reconfigured with an ACL instead of an ip prefix - list command.
D . Router R1 will deny the 172.16.1.0/27 route while permitting the 172.16.1.0/26 route to be advertised.
-
Refer to the exhibit. In this network，R1 is configured not to perform autosummarization within EIGRP. What routes will R3 learn from R2 through EIGRP？（）https://assets.asklib.com/images/image2/2018072317150093827.jpg
A . 172.30.1.0/24 and 10.1.2.0/24；EIGRP only performs autosummarization at the edge between two major networks
B . 172.30.0.0/16 and 10.1.2.0/24；R2 will perform autosummarization，although R1 will not
C . Since R2 is configured without autosummarization，it will not propagate the 172.30.1.0/24 route
D . 172.30.0.0/8 and 10.0.0.0/8
-
Refer to the exhibit. What statement is true based upon the configuration of router R1 and router R2？（）https://assets.asklib.com/images/image2/2018073015422145313.jpg
A . Router R2 will become the master for Virtual Router 1， and router R1 will become the backup for Virtual Router 2.
B . Router R1 will become the master for Virtual Router 1， and router R2 will become the backup for Virtual Router 2.
C . Router R1 will become the active virtual gateway.
D . Router R2 will become the active virtual gateway.
E . The hello and hold timers are incompatible with OSPF type 5 LSAs.
F . The hello and hold timers are incompatible with multi-homed BGP.
-
Refer to the exhibit.Based on the exhibited routing table,how will packets from a host within the 192.168.10.192/26 LAN be forwarded to 192.168.10.1?（）https://assets.asklib.com/images/image2/2018072408493768982.jpg
A . TherouterwillforwardpacketsfromR3toR2toR1
B . TherouterwillforwardpacketsfromR3toR1
C . TherouterwillforwardpacketsfromR3toR1toR2
D . TherouterwillforwardpacketsfromR3toR2toR1ANDfromR3toR1
-
Refer to the exhibit. On the basis of the configuration that is provided, how would the BGP updates that come from router R1 be replicated inside autonomous system 65200？（）https://assets.asklib.com/images/image2/2018073011571469196.jpg
A . All BGP updates that are received on router R 2 will be sent to routers R3 and R4. Routers R3 and R4 will then forward those BGP updates to router R5
B . None of the BGP updates that are received on router R2 will ever be received by router R5
C . All BGP updates that are received on router R2 will not be sent to routers R3 and R4
D . All BGP updates that are received on router R2 will be sent directly to router R5
-
Refer to the exhibit. According to the routing table, where will the router send a packet destined for 10.1.5.65?（）https://assets.asklib.com/images/image2/2018072408541982136.jpg
A . 10.1.1.2
B . 10.1.2.2
C . 10.1.3.3
D . 10.1.4.4
-
Refer to the exhibit. How would you confirm on R1 that load balancing is actually occurring on the default - netw ork （0.0.0.0)？（）
<img src='https://img2.soutiyun.com/ask/uploadfile/2019-03-27/ae2677f0b95075ecbebd837f23ecac04.jpg' />
A. Use ping and the show ip route command to confirm the timers for each default network resets to 0.
B. Load balancing does not occur over default networks; the second route will only be used for failover.
C. Use an extended ping al ong with repeated show ip route commands to confirm the gateway of last resort address toggles back and forth.
D. Use the traceroute command to an address that is not explicitly in the routing table.
-
Refer to the exhibit. What additional commands should be used to configure OSPF area 5 as a Totally Stubby area？ （）
<img src='https://img2.soutiyun.com/shangxueba/ask/64290001-64293000/64291910/529008d927b67f31920b5858e5879e0b.png' />
A. area 0 stub o n routers R4 and R5
B. area 5 stub on routers R4 and R5
C. area 5 stub no - summary on routers R4 and R5
D. area 0 stub no - summary on router R4 and area 5 stub no - summary on router R5
E. area 5 stub no - summary on router R4 and area 5 stub on router R5
-
Refer to the exhibit. When running OSPF, What would cause router A not to form an adjacency with router B？（）
<img src='https://img2.soutiyun.com/ask/uploadfile/2019-03-27/67e52e69e1cc511a71a60a5d0c35c68a.jpg' />
A.The loopback addresses are on different subnets
B.The value of the dead timers on the router are different
C.Route summarization is enabled on both routers
D.The process indentifier on router A is different than the process identifier on router B
