-
Which line from the output of the show ip interface command indicates a layer 1 problem?（）
A . Serial0/1 is up, line protocol is down
B . Serial0/1 is down, line protocol is down
C . Serial0/1 is up, line protocol is up
D . Serial0/1 is administratively down, line protocol is dow
-
Which of the following commands would be applied to a WAN interface, but not on LAN Interface?（）
A . IP address
B . encapsulation PPP
C . no shutdown
D . PPP authentication CHAP
E . Speed
F . None of the above
-
You need make configuration changes to an existing layer 3 switch in the Company network. On a multilayer Catalyst switch， which interface command is used to convert a Layer 3 interface to a Layer 2 interface？（）
A . switchport access vlan vlan-id
B . switchport
C . switchport mode access
D . no switchport
E . None of the other alternatives apply
-
Which two statements about an interface configured with the asr-group command are correct?（）
A . The FWSM supports up to 16 asymmetric routing groups.
B . If a matching packet is not found, the packet is dropped.
C . Asymetric routing of return traffic is enabled.
D . If a matching packet is found, the Layer 3 header is rewritten.
E . If a matching packet is found, the Layer 3 header is rewritten and the packet is forwarded to the default gateway.
-
Which of the following commands will display the active heartbeat sensitivity of network interface modules（NIMs）？（）
A . cllsnim a
B . lssrc -ls grpsvcs
C . lssrc ls topsvcs
D . cllstopsvcs -G -t dh
-
Which command can be used to determine the type of cable attached to the Serial 0/0 interface on a router?（）
A . show interfaces serial 0/0
B . show running-config
C . show version
D . show controllers serial 0/0
E . show ip interface
F . show line serial 0/0
-
Which command will assign the last usable IP address from the 192.168.32.128/28 subnetwork to a router interface?（）
A . TestKingA(config-if)# ip address 192.168.32.142 255.255.255.240
B . TestKingA(config-if)# ip address 192.168.32.143 255.255.255.240
C . TestKingA(config-if)# ip address 192.168.32.158 255.255.255.240
D . TestKingA(config-if)# ip address 192.168.32.145 255.255.255.240
E . TestKingA(config-if)# ip address 192.168.32.144 255.255.255.240
-
which command is used to enable CHAP authentication whit PAP as the fallback method on a serial interface?（）
A . (config-if)#authentication ppp chap fallback ppp
B . (config-if)#authentication ppp chap pap
C . (config-if)#ppp authentication chap pap
D . (config-if)#ppp authentication chap fallback
-
When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?（）
A . show ip access-list
B . show access-list
C . list ip interface
D . show interface
E . show ip interface
-
Which two IOS commands are equivalents for putting a Cisco 7500 OC-12 RPR interface card intowrapped mode？ （）
A . shutdown [a b]
B . srp shutdown [a b]
C . srp ips request manual-switched [a b]
-
Which of the following commands should be used to list all of the active network interfaces on a system？（）
A . lscfg
B . route
C . netstat
D . entstat
-
Which command shows if an access list is assigned to an interface?（）
A . show ip interface [interface] access-lists
B . show ip access-lists interface [interface]
C . show ip interface [interface]
D . show ip access-lists [interface]
-
Which dose the frame-relay interface-dlinterface-dlcci command configure?（）
A . remote DLCI on the main interface
B . local DLCI on the main interface
C . local DLCI on the subinterface
D . remote DLCI on the subinterface
-
Which of the following commands indicates the packet count for each interface？（）
A . lsattr
B . route
C . netstat
D . ifconfig
-
Which is a command-line scripting interface based on Jython used for automation of WebLogic Server administration ？（）
A . WebLogic Scripting Tool
B . Weblogic OPMN
C . WeblogicDeployer
D . WeblogicICommand
-
Which of the following pieces of information will the command show interface provide？（Choose allthat apply.）（）
A . Layer 1 status
B . Output queue drops
C . Interface CPU utilization
D . Cable type connected to interface
E . Layer 2 status
F . Input queue dro
-
Which routing protocol will continue to receive and process routing updates f rom neighbors after the passive - interface router configuration command is entered?（）
A . EIGRP
B . RIP
C . OSPF
D . IS - IS
-
Which of the following commands on the wireless interface of a Cisco 3845 Integrated Services Router allows the SSID to broadcast？（）
A . router （config-ssid）# guest-mode
B . router （config-ssid）# advertise
C . router （config-ssid）# enable
D . router （config-ssid）# broadcast
-
Refer to the show interface Gi0/1 switchport command output shown in the exhibit. Which twostatements are true about this interface？（）https://assets.asklib.com/images/image2/2018072615453856014.jpg
A . This interface is a member of a voice VLAN
B . This interface is a dot1q trunk passing all configured VLANs
C . This interface is a member of VLAN7
D . This interface is configured for access mode
E . This interface is a member of VLAN1
-
Which of the following commands on the wireless interface of a Cisco 3845 Integrated Service Router allows the SSID to broadcast？（）
A . router（config-ssid）# enable
B . router（config-ssid）# advertise
C . router（config-ssid）# broadcast
D . router（config-ssid）# guest-mode
-
Which command shows if an access list is assigned to an interface？（）
A . show ip interface [interface] access-lists
B . show ip access-lists interface [interface]
C . show ip interface [interface]
D . show ip access-lists [interface]
-
Which of the following commands on the wireless interface of a cisco 3845 integrated service router allows the ssid to broadcast？（）
A . router（config-ssid）# enable
B . router（config-ssid）# advertise
C . router（config-ssid）# broadcast
D . router（config-ssid）# guest-mode
-
Referring to the exhibit, which command would you use to add an additional address to the ge-0/0/9 unit 0 interface？（）
<img src='https://img2.soutiyun.com/shangxueba/ask/17124001-17127000/17126130/8d1b0ad62b4fb18bb984b0a4dcbe0ff7.jpg' />
A. [edit interfaces ge-0/0/9 unit 0] user@router set family inet address 192.168.100.1/24
B. [edit interfaces ge-0/0/9 unit 0] user@router set family inet secondary-address 192.168.100.1/24 secondary
C. [edit interfaces ge-0/0/9 unit 0] user@router set family inet address 192.168.100.1/24 secondary
D. [edit interfaces ge-0/0/9 unit 0] user@router set family inet address-secondary 192.168.100.1/24
