-
In setting the valves on a steam-smothering system on a tank vessel,the master control valve to cargo tanks should be().
A . open and individual tank valves open
B . open and the individual tank valves closed
C . closed and the individual tank valves closed
D . closed and the individual tank valves ope
-
Safety valves on a boiler vent to the ().
A . fuel tank
B . bilge
C . atmosphere
D . auxiliary exhaust line
-
The needle valve will open when the fuel pressure acting on the needle valve () exerts a sufficient force to overcome the spring compression.
A . tape face
B . tapered face
C . surface
D . thinner face
-
In setting the valves on a steam-smothering system on a tanker,the master control valve to cargo tanks should be().
A . open and individual tank valves open
B . open and the individual tank valves closed
C . closed and the individual tank valves closed
D . closed and the individual tank valves ope
-
The bypass valve on a self-contained breathing device should be opened if().
A . you are entering a space containing poisonous vapors
B . you are entering a space containing explosive gases
C . the regulator of the breathing apparatus malfunctions
D . the face piece of the breathing device is too tight
-
A ruptured diaphragm in a thermostatic expansion valve will cause the valve to ().
A . open
B . close
C . remain in its position
D . flood the evaporator with refrigerant
-
Which of the problems listed represents the major difficulty encountered with thermal expansion valve operation?()
A . Lube oil passing through the system
B . Moisture or foreign matter collecting at the valve seat and orifice
C . Variable spring tension caused by the changing temperature
D . Frost on the liquid line
-
A branch line valve of a fire extinguishing system on a ship must be marked with the().
A . maximum pressure allowed at that branch
B . name of the space or spaces which it serves
C . date of the last maintenance inspection
D . pressure needed to maintain an effective stream at that point
-
If the relief valve on the discharge side of a hydraulic pump lifts, the cause could be ().
A . a low load on the unit
B . a clogged pump suction strainer
C . a blockage in the line between the pump and hydraulic motor
D . the hydraulic motor turning too fast
-
Dirt lodged on the nozzle valve seat of a fuel injection nozzle will cause()
A . erosion and cratering of the nozzle orifices
B . fuel leakage into the nozzle drain line
C . fuel leakage before and after injection
D . insufficient fuel delivery though that nozzle
-
Which of the following configuration is valid for expansion drawers on a Power 750 with 2 processor board sinstalled?()
A . 3 PCI-e I/O drawers and 1 PCI-X I/O drawer
B . 4 PCI-e I/O drawers and 4 RIO-2 I/O drawers
C . 2 PCI-e I/O drawers and 4 PCI-x I/O drawers
D . 4 PCI-e I/O drawers and 2 PCI-X I/O drawer
-
Operation of the valve control release on a fixed CO2 system must immediately().
A . release CO
to the protected space
B . secure all mechanical ventilation in the protected space
C . sound the rig's general alarm signal for a fire
D . sound an alarm in the ballast control room
-
A feeler or thermal bulb is used for the expansion valve to ().
A . detect the temperature
B . detect the pressure
C . heat the refrigerant
D . accelerate the refrigerant
-
The needle valve in a fuel valve will () when the fuel pressure action on the needle valve tapered face exerts a force lower than that of the spring compression.
A . be jammed
B . be opened
C . be seated
D . be broke
-
The thermal expansion valve responds to the()
A . amount of superheat in the vapor leaving the coil
B . amount of superheat in the liquid
C . temperature in the evaporator coils
D . pressure in the evaporator coil
-
A thermostatic expansion valve is properly controlling evaporator superheatAdjusting this valve to lower the superheat will result in a/an ().
A . evaporator pressure decrease
B . evaporator coil over-feed
C . evaporator capacity increase
D . expansion valve diaphragm rupture
-
The expansion tank for a diesel engine closed cooling system is designed to maintain a constant head on the system and ().
A . reduce water temperature
B . reduce water turbulence
C . provide an air cushion
D . allow for an increase in water volume as the engine warms u
-
The bulb for the thermal expansion valve is located()
A . in the middle of evaporator coils
B . near the evaporator coil outlet
C . near the evaporator coil inlet
D . on the bottom row of evaporator coil
-
If the relief valve on a diesel engine cylinder lifts, the cause could be due to ()
A . liquid in the cylinder
B . low compression in the cylinder
C . high exhaust temperature
D . poor fuel penetratio
-
A cracked diaphragm in a thermostatic expansion valve will cause the valve to ().
A . return to a neutral position
B . flood the evaporator
C . open
D . close
-
Which of the listed statements is a characteristic of the liquid charged power element used with thermostatic expansion valves?()
A . At the designed operating temperature, the liquid refrigerant charge has changed to a vapor
B . The liquid refrigerant tends to collect at the bellows or diaphragm and reduces the valve sensitivity
C . The sensing bulb is empty of liquid refrigerant charge at the designed operating temperature
D . The sensing bulb is never emptied of liquid refrigerant under normal operating conditio
-
When a refrigeration compressor is in the ‘off’ cycle, the thermal expansion valve will().
A . always be wide open when the compressor restarts
B . continue to operate as if the system were in operation
C . remain open until evaporator pressure equalizes, then close until the compressor restarts
D . always be completely closed until the compressor restart
-
Which of the following four CRS components must be active on a Historical Reporting Database (HRDB) and Call Recording expansion server?()
A . CRS Node Manager
B . CRS Engine
C . Cisco Recording
D . CRS Application Editor
E . Cisco Monitoring
F . CRS Repository Datastore, CRS Historical Datastore, CRS Config Datastore, CRS Agent Datastore
-
When a refrigeration compressor is in the ‘off’ cycle, the thermal expansion valve will .
A.always be wide open when the compressor restarts
B.continue to operate as if the system were in operation
C.remain open until evaporator pressure equalizes, then close until the compressor restarts
D.always be completely closed until the compressor restarts