The VDR system is designed to operate（）once it is set up correctly.There is no user interaction.
A . automatically
B . accurately
C . promptly
D . conspicuously
相似题目
-
An inert gas system is designed to reduce the possibility of tank explosions by（）.
A . eliminating sparks and fire in the vicinity of cargo tanks
B . removing all hydrocarbon gases from the cargo tanks
C . blanketing cargo tanks with inert foam
D . reducing the oxygen concentration below levels necessary for combustio
-
A customer has 5 older POWER5 systems and they want to consolidate them onto a POWER6 system. What information is important to analyze when deciding how to design the new machine using the System Planning Tool?（）
A . vmstat and iostat data from the older machines
B . The number of CPUs that were installed in the original machines
C . Data from Workload Estimator (WLE) and IBM Performance Management (PM)
D . Performance data that is collected from the new system after it has been put into productio
-
Which of the following statements is correct for the design and installation of diesel engine cooling water systems?（）
A . An alarm device with audible and visible signals is required for all cooling water systems
B . Propulsion engines with bores over 200 mm are to be fitted with cooling water jackets
C . Each totally enclosed cooling system shall be provided with a suitable head tank
D . Drain cocks are to be provided at the lowest points of all cylinder water jacket
-
Lubricating systems for diesel engines are usually designed to initially provide lube oil to the engine （）
A . camshaft beatings
B . main bearings
C . piston crowns
D . cylinder wall
-
Which storage system is this statement describing: A high-end, disk storage system with a virtualized grid architecture designed to eliminate the complexity of storage administration and make managing storage easy.（）
A . XIV system
B . SONAS
C . DS8800
D . N serie
-
Click the Exhibit button. When designing a DWDM system with multiple amplified spans， a pre-amp is needed at Site B to （）.https://assets.asklib.com/images/image2/2018080113561481444.jpg
A . offset the OADM loss at site B
B . overcome the high multiplexer loss at site A
C . amplify signal levels after the high loss through Fiber Span 1
D . adjust add channels at site B to be at the same level as the passthrough channels
E . ensure that the per channel power is higher than the minimum needed for the post-amp at Site B
-
Which of the following best describe the customer benefit of creating a systems acceptance test plan in the design phase？（）
A . Reduce unnecessary disruption， delay，rework， and other problems by establishing test cases for use in verifying that the systems meets operational， functional， and interface requirements
B . Improve its ability to make sound financial decisions by developing a business case based on its business requirements and establishing a basis for developing a technology strategy
C . Reduce operating costs and limit charge-related incidents by providing a consistent and efficient set of processes
D . Improve the return on investment and hasten migration by identifying and planning for necessary infrastructure changes and resource additions， as well as reduce deployment costs by analyzing gaps in early in the planning process to determine whet is needed to support the system
-
A （）, sometimes called filters, is a device designed to prevent the passage of unwanted solids into the system.
A . steam trap
B . check valve
C . separator
D . strainer
-
The IBM XIV Storage System is designed to be cost-efficient in all aspects, while deliveringoutstanding and consistent performance. Which of these features is currently UNAVAILABLE onthe XIV system?（）
A . single-tier architecture supports all kinds of storage in one environment and makes scaling easy
B . built-in thin-provisioning allows the acquisition and installation of additional capacity to bedelayed until needed.
C . innovative use of solid state disk drives offers excellent capacity-for-cost value while meetingenterprise performance standards
D . use of off-the-shelf components makes customized hardware unnecessary and makes itpossible to integrate state-of-the-art hardware assoon as it becomes available.
-
You need to recommend a configuration design for the new VMs. The design must ensure that operating systems can be deployed to the new VMs. What should you include in the recommendation？（）
A . virtual machine queue （VMQ）
B . Virtual Machine Chimney
C . a synthetic network adapter
D . an emulated network adapter
-
The expansion tank for a diesel engine closed cooling system is designed to maintain a constant head on the system and （）.
A . reduce water temperature
B . reduce water turbulence
C . provide an air cushion
D . allow for an increase in water volume as the engine warms u
-
（）sometimes called filter, is a device designed to prevent the passage of unwanted solids into the system.
A . Steam trap
B . Check valve
C . Separator
D . Strainer
-
Click the Exhibit button. When designing a DWDM system with multiple amplified spans, a pre-amp is needed at Site B to （）. (Choose three.)https://assets.asklib.com/images/image2/2018080114074365428.jpg
A . offset the OADM loss at site b
B . overcome the high multiplexer loss at site a
C . amplify signal levels after the high loss through Fiber Span 1
D . adjust add channels at site B to be at the same level as the passthrough channels
E . ensure that the per channel power is higher than the minimum needed for the post-amp at Site
-
Which operating system is NOT supported by Domino Designer 8.5.1？（）
A . SUSE Linux Enterprise Desktop （SLED）
B . Microsoft Windows XP Professional SP2+
C . Microsoft Windows XP Tablet PC Edition
D . Microsoft Vista Ultimate
-
In a Cisco Unified Computing System， What is the "designated receiver" port in end-host mode used for？（）
A . Sending all broadcasts
B . Receiving all traffic from upstream switches
C . Receiving broadcast traffic
D . Negotiating spanning tree with upstream switches
E . Learning MAC addresses from upstream switche
-
Generally speaking, a CAD system is an analytic tool for design.
-
43. The VDR system is designed to operate ____once it is set up correctly. There is no user interaction.
-
The system has been designed to give students quick and easy _____ to the digital resources of thelibrary.
-
The method used during design and manufacturing to determine the impact of a product or system on the environment.
A) Life cycle analysis
B) Life cycle inventory
C) Systemsapproach
D) Characterization
-
____ is the most important and complex stage in the product design process, and it is also the stage most restricted by the designer's creative inspiration. ( ).
Prototype design
The concept design
The visual design
Industrial design
-
Flowcharting is used primarily for program design and rarely for systems design.（)
是
否
-
The compatibility of pneumatic equipment is the responsibility of the person who designs the pneumatic system or decides its specifications.
-
There are three IS-IS routers on a Gigabit Ethernet segment: Router A, Router B, and Router C. Each router is configured in the same area and each routers Gigabit Ethernet interface is configured for Level 1-only. Router A is the Designated Intermediate System (DIS). Each routers IP address on that segment is:Router A: 10.1.1.1/24Router B: 10.1.1.2/24Router C: 10.2.2.1/26Which statement is true about all the adjacencies that exist on that LAN？（）
A. No routers are adjacent with each other.
B. Only Router A and Router B are adjacent at Level 1.
C. Only Router A and Router B are adjacent at Level 2.
D. All three routers are adjacent with each other at Level 1.
-
（翻译）1． SQL Server is designed to allow thousands of users to access the database at the same time and is a true client/server database system.2． An application software is any program designed to perf
