-
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）
A . Router(config)#router ospf 1
B . Router(config)#router ospf 0
C . Router(config)#router ospf area 0
D . Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
E . Router(config-router)#network 192.168.16.0 0.0.0.255 0
F . Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
-
After adding a new Ethernet card to a system and rebooting， the system administrator notices the card was not configured. How can the system administrator determine if there were errors during the configuration process for the card？（）
A . Examine the bootlog with the command： alog -o -f /var/adm/ras/bootlog
B . Display the device attributes and errors with the command： lsdev -C -l ent0
C . Examine the AIX errlog for configuration method errors with the command： errpt -a -C ent0
D . Examine the ODM for configuration errors with the command： odmget -q "method_errors" ent0
-
Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0？（）
A . Router（config）#router ospf 1
B . Router（config）#router ospf 0
C . Router（config）#router ospf area 0
D . Router（config-router）#network 192.168.16.0 0.0.0.255 area 0
E . Router（config-router）#network 192.168.16.0 0.0.0.255 0
F . Router（config-router）#network 192.168.16.0 255.255.255.0 area 0
-
The SQL Tuning Advisor has been configured with default configurations in your database instance. Which recommendation is automatically implemented without the DBA's intervention after the SQL Tuning Advisor is run as part of the AUTOTASK framework?（）
A . statistics recommendations
B . SQL profile recommendations
C . index-related recommendations
D . restructuring of SQL recommendatio
-
Refer to the exhibit.HostA cannot ping HostB.Assuming routing is properly configured,what could be the cause of this problem?（）
A . HostA is not on the same subnet as its default gateway
B . The address of SwitchA is a subnet address
C . The Fa0/0 interface on RouterA is on a subnet that cannot be used
D . The serial interfaces of the routers are not on the same subnet
E . The Fa0/0 interface on RouterB is using a broadcast addre
-
What should the configuration register value be after successfully completing the password recover procedure and returning the router to normal operation? （）
A . 0x2100
B . 0x2101
C . 0x2102
D . 0x2124
E . 0x2142
-
The SQL Tuning Advisor has been configured with default configurations in your database instance. Which recommendation is automatically implemented without the DBA’s intervention after the SQL Tuning Advisor is run as part of the AUTOTASK framework？（）
A . statistics recommendations
B . SQL profile recommendations
C . index-related recommendations
D . restructuring of SQL recommendatio
-
An administrator created a WebSphere Commerce instance but the site is not performing properly. The log messages don’t give enough information to determine the problem. Which tool is used to configure tracing of WebSphere Commerce？（）
A . WebSphere Commerce Configuration Manager
B . WebSphere Application Server Administrative Console
C . WebSphere Commerce Administration Console
D . WebSphere Commerce Accelerator
E . Command line
-
A company is deploying a Microsoft Windows-based， mission-critical Data Warehousing application. The customer has specified 4GB of RAM. Which TWO of the following questions will best help the consultant determine the proper memory configuration？（）
A . Does the application require a large paging space？
B . What is the anticipated memory/disk cache hit ratio？
C . Does the application support Physical Address Extensions （PAE）？
D . Are there future plans to expand the amount of memory in the system？
E . Do the application availability requirements justify the use of Memory Mirroring technologies？
-
Refer to the exhibit.HostA cannot ping HostB.Assuming routing is properly configured，what could be thecause of this problem？（）https://assets.asklib.com/images/image2/2018072315055477964.jpg
A . HostA is not on the same subnet as its default gateway
B . The address of SwitchA is a subnet address
C . The Fa0/0 interface on RouterA is on a subnet that cannot be used
D . The serial interfaces of the routers are not on the same subnet
E . The Fa0/0 interface on RouterB is using a broadcast addre
-
Which routing protocol will continue to receive and process routing updates f rom neighbors after the passive - interface router configuration command is entered?（）
A . EIGRP
B . RIP
C . OSPF
D . IS - IS
-
If an edge Label Switch Router （LSR） is properly configured，which three combinations are possible？（）
A . A received IP packet is forwarded based on the IP destination address and the packet is sent as an IP packet.
B . An IP destination exists in the IP forwarding table. A received labeled packet is dropped because the label is not found in the LFIB table.
C . There is an MPLS label-switched path toward the destination. A received IP packet is dropped because the destination is not found in the IP forwarding table.
D . A received IP packet is forwarded based on the IP destination address and the packet is sent as a labeled packet.
E . A received labeled IP packet is forwarded based upon both the label and the IP address.
F . A received labeled packet is forwarded based on the label. After the label is swapped，the newly labeled packet is sent.
-
Oracle Net Configuration Assistant is a post-installation tool that configures basic network components after installation. Which four components are included in the configuration？（）
A . Directory server
B . Hostname adaptor
C . TCP/IP host file
D . Connection Manager
E . connecting pooling
F . external procedures
G . listener names and protocol addresses
H . Net Service names in a tnsnames.ora file
I . naming methods the client uses to resolve connect identifier
-
Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）
A . Router(config)#router ospf 1
B . Router(config)#router ospf 0
C . Router(config)#router ospf area 0
D . Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
E . Router(config-router)#network 192.168.16.0 0.0.0.255 0
F . Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
-
What three tasks must a network administrator perform to properly configure Hot Standby Routing Protocol （HSRP）？（）
A . Define the encapsulation type.
B . Define the standby router.
C . Define the standby IP address.
D . Enable the standby priority.
-
Which two passwords must be supplied in order to connect by Telnet to a properly secured Cisco switch and make changes to the device configuration? (Choose two.)（）
A . console password
B . vty password
C . aux password
D . tty password
E . enable secret password
F . username password
-
A system administrator needs to replace a mirrored disk. After performing the proper removal process and replacing the disk, which of the following set of commands should be performed to bring the disk back into production?（）
A . reboot, mklvcopy, syncvg
B . cfgmgr -vl ssar, chvg -va, syncvg
C . cfgmgr, extendvg, syncvg
D . extendvg, mklvcopy, syncvg
-
Which configuration is required for a Vocera badge to function properly on a Cisco WLC?（）
A . disable higher data rates
B . set DTIM = 1
C . disable RRM
D . disable broadcast SSID
E . disable multicast
-
Which commands are required to properly configure a router to properly configure a router to run OSPFand to add network 192.168.16.0/24 to OSPF area 0？（）
A . Router（config）#router ospf 1
B . Router（config）#router ospf 0
C . Router（config）#router ospf area 0
D . Router（config-router）#network 192.168.16.0 0.0.0.255 area 0
E . Router（config-router）#network 192.168.16.0 0.0.0.255 0
F . Router（config-router）#network 192.168.16.0 255.255.255.0 area 0
-
I’m ( ) to go jogging after work. (Fill the blank with a proper word.)
-
【单选题】I’m ( ) to go jogging after work. (Fill the blank with a proper word.) 答案:going
-
I’m ( ) to go jogging after work. (Fill the blank with a proper word.) 答案:going
-
The SQL Tuning Advisor has been configured with default configurations in your database instance.Which recommendation is automatically implemented without the DBA‘s intervention after the SQL Tuning Advisor is run as part of the AUTOTASK framework？（）
A. statistics recommendations
B. SQL profile recommendations
C. index-related recommendations
D. restructuring of SQL recommendations
