-
If the speed of a turbocharged diesel engine is maintained constant the turbocharger speed will ()
A . decrease until the engine speed increases
B . increase as the load increases
C . decrease as the load
D . increases remain unchanged
-
Increasing the load on an engine equipped with a constant speed mechanical governor, will cause the engine speed to initially ().
A . increase
B . decrease
C . fluctuate
D . remain constant
-
An over-speed trip stops a diesel engine when the engine ()
A . runs out of fuel
B . has low lubricating oil pressure
C . exceeds a set maximum speed
D . has high cooling water temperature
-
When attempting to start a main propulsion diesel engine, the engine, the engine turns at the proper speed but will not startYou should check the()
A . starting air pressure
B . scavenge air pressure
C . over-speed trip
D . banjo oiler line
-
On a turbo-charged, medium-speed diesel engine, which of the following problems is an indication of a restricted air intake passage?()
A . Engine is hard to start
B . Engine misses
C . Surges at governed RPM
D . Coolant temperature is too low
-
On a diesel engine equipped with an isochronous governor, if the “speed droop” control is reduced to the “zero” setting, the engine ()
A . speed will drop drastically with any increase in load
B . will stop due to zero fuel supply
C . will stall upon application of load
D . speed will remain fairly constant despite load change
-
An emergency generator, driven by an internal combustion engine, shall be tested under load for a minimum of 2 hours at least once every ()
A . week
B . 2 weeks
C . month
D . 3 month
-
The device used to limit engine torque at various engine speeds is called a ()
A . speed limiting governor
B . variable speed governor
C . constant speed governor
D . load limiting governor
-
An individual injection pump is designed for variable beginning and constant ending of injectionFor diesel engines operating at constant speeds, the start of injection will()
A . advance as the load increases
B . retard as the load increase
C . remain unchanged regardless
D . always occur at top dead center
-
The opening of an exhaust valve on a modem, large, low-speed, main propulsion diesel engine may be actuated by ().
A . direct action of cam shaft
B . compressed air pressure
C . hydraulic “push rods”
D . direct action of the main piston moving dow
-
The ability of the governor to prevent fluctuations in engine speed is termed ().
A . sensitivity
B . stability
C . promptness
D . speed droo
-
On a large low-speed main propulsion diesel engine, lower main bearing wear is usually measured by using a/an ()
A . dial indicator
B . outside caliper
C . bridge gauge
D . tram rod
-
An increase in load on a diesel engine results in () of speed of the crankshaft.
A . a reduction
B . an increase
C . an outing
D . a downward
-
Each cylinder liner on the marine medium speed engines ().
A . is usually cooled by sea water
B . can be replaced when worn out
C . is in direct contact with the water in the bore of the cylinder
D . can t expand when heated
-
What is the minimum recommended uplink/downlink speed to support a single encrypted IP voice Teleworker call?()
A . 256kbps / 1024kbps
B . 256kbps / 1544kbps
C . 160kbps / 768kbps
D . 384kbps / 384kbps
E . 128kbps / 512k
-
The hydraulic () is used to control engine speed.
A . motor
B . pump
C . governor
D . capsta
-
The majority of medium speed and high speed marine diesel engines for main or auxiliary drive operate on the () cycle.
A . two-stroke
B . four-stoke
C . long-stroke
D . short-stroke
-
An electrically driven automatically operating auxiliary blower is provided for slow speed and () of a low speed diesel engine.
A . manoeuvring operations
B . bad combustion
C . cooling
D . mooring trial
-
“The engine not obtaining the sufficient speed for firing” means that ().
A . the start fails
B . the fuel pumps will be put into operation
C . the fuel valves are damaged
D . the combustion process will take over
-
On most diesel engines, the governor controls the output speed by ().
A . controlling the amount of fuel injected into the cylinders
B . varying the speed of the turbocharger
C . adjusting the compression ratio
D . changing the timing of the fuel injection camshaft
-
Critical speeds occurring within the operating speed range of a main propulsion diesel engine may be changed, or have their damaging effects reduced by a/an ()
A . engine support vibration isolator
B . detuner or viscous fluid damper
C . lightened crankshaft flywheel
D . spherically seated crankshaft bearing
-
If it becomes necessary to cutout an individual cylinder of a large, low-speed, main propulsion diesel engine, the fuel to that cylinder should be secured and its ()
A . fuel pump should be removed and all connections blanked off
B . cylinder oil feed rate should be increased slightly above that used at normal sea speed
C . cylinder oil feed rate should be reduced
D . cylinder oil feed rate should be increased to the maximum flow capable of the metering pum
-
While the maximum speed limit on China’s expressways is set, there is no minimum speed limit on expressways in China.
-
If a four-engine air carrier airplane is dispatched from an airport that is below landing minimums, what is the maximum distance that a departure alternate airport may be located from the departure ai
A、Not more than 2 hours at cruise speed with one engine inoperative
B、Not more than 2 hours at cruise speed in still air with one engine inoperative
C、Not more than 1 hour at cruise speed in still air with one engine inoperative