机床报警LaserH-Voltage not ready是()
A . 机床没回参考点
B . 激光器没上高压
C . 没开切割气体空气或氧气
相似题目
-
在对长期不使用的数控机床空运转通电运行时,要及时发现有无()报警信号,避免系统软件的参数丢失。
A . 数据
B . 系统
C . 电池
D . 电源
-
机床进给伺服系统故障报警现象有哪几种?
-
引起数控机床主轴伺服系统过载报警的原因有哪些?
-
机床发生超程报警的原因不太可能是()。
A . 刀具参数错误
B . 转速设置错误
C . 工件坐标系错误
D . 程序坐标值错误
-
机床报警Cuttinggas not ready是()
A . 机床没回参考点
B . 激光器没上高压
C . 没开切割气体空气或氧气
-
排除数控机床某轴超程报警的可行办法是()。
A . 关闭数控系统电源
B . 按下急停按钮
C . 手动反向运动该轴
D . 切掉该轴限位开关电源
-
数控外圆磨机床报警2042是()
A . 液压油不足
B . 砂轮停止
C . 冷却液不足
D . 静压油不足
-
操作人员可根据数控机床的报警信号进行分析,缩小检查范围,有目的地进行某个方面的检查。
A . 正确
B . 错误
-
数控车床具有自动()功能,根据报警信息可迅速查找机床事故。而普通车床则不具备上述功能。
A . A.报警
B . B.控制
C . C.加工
D . D.定位
-
数控外圆磨床机床报警2041是()
A . 液压未开
B . 静压未开
C . 冷却液缺少
D . 砂轮未开
-
当润滑泵中的润滑油位()最低液面时,数控机床面板上的润滑报警指示灯亮。
A . 高于
B . 等于
C . 低于
D . 高于等于
-
数控机床的故障按故障特征分类,可分为()和有报警故障两大类。
A . 随机性故障
B . 无报警故障
C . 可恢复性故障
D . 机械故障
-
按下“()按钮”,解除控制机报警状态,机床即可恢复正常工作状态。
A . RESET
B . AUX
C . ON
D . OFF
-
机床加工过程中出现异常或系统报警时,应立即停机并报告指导老师,待正常后方可继续操作。
A . 正确
B . 错误
-
XK5025数控铣床配备Fanuc-0i mate系统,机床运行中突然出现急停报警,按强电复位键不能复位,机床锁住。不能复位的原因有可能是()。
A . 串接在行程开关的空气开关脱扣
B . 接触器、继电器故障,PLC急停信号不能复位
C . 复位按钮故障,PLC急停信号不能复位
D . 编码器故障,检测不到零点脉冲信号
E . 行程开关故障
-
数控机床CRT上显示“NOT READY”,主要原因是()。
A . 伺服系统故障
B . 数控系统故障
C . PLC故障
D . 程序错误
-
数控内圆磨机床2000报警是()
A . 油气压力不正常
B . 机床变频器故障
C . 机床电机故障
D . 冷却液不足
-
机床报警Reference not down是()
A . 机床没回参考点
B . 激光器没上高压
C . 没开切割气体空气或氧气
-
The word far-reaching could be divided as far-rea-ching.
-
数控系统的报警大体可以分为操作错报警、程序错误报警、驱动报警及系统错误报警等, 某机床在运行过程中出现“指令速率过大”报警,这属于( )。
-
Not only ______ the book, but he remembered what he had rea
A.he had read
B.he read
C.he did read
D.did he read
-
The theatre did not burn down. Firefighters arrived quickly after the alarm(报警) and put
The theatre did not burn down. Firefighters arrived quickly after the alarm(报警) and put out the fire so fast that no more than the seat coverings were burned. However, 602 people died, and many more were injured. Panic(惊慌), not the fire itself, caused the tragedy(悲剧).
A similar disaster occurred on a July morning in 1990 in the city of Mecca. Thousands of people were walking through a 600-yard-long tunnel(隧道) when the lights accidentally went out. Panic started the frightened people pushing their way through the tunnel and 1,426 people were killed.
The people in the Theatre and the Mecca tunnel behaved as people often do when faced with unexpected and dangerous situations such as fires, earthquakes, and floods: they panicked. Panic is one of the more extreme types of grouped people's behavior. It is a useless response to a serious threat or danger. It generally involves flight, but it is a special kind of flight. However, in panic behavior, the flight is unwise and unhelpful. It follows a loss of self-control, and it increases, rather than reduces, danger to oneself and others.
Worst Killer in Time of Danger
The number of people died in the theatre fire:【46】
The main cause of the deaths in the fire: People's【47】not the fire itself
The length of the tunnel mentioned:【48】
Result of flight in time of danger: 1)【49】of self-control
2) increase of【50】
-
机床导轨欠油报警后,将导轨油注入邮箱,就能解除警报()
是
否
-
机床通电后,在手动方式或自动方式运行时X轴出现爬行,无任何报警显示()
是
否