-
Refer to the exhibit. In this network， R1 is configured not to perform autosummarization within EIGRP. What routes will R3 learn from R2 through EIGRP？ （）https://assets.asklib.com/images/image2/2018072318005941808.jpg
A . 172.30.1.0/24 and 10.1.2.0/24；EIGRP only performs autosummarization at the edge between two major networks.
B . 172.30.0.0/16 and 10.1.2.0/24；R2 will perform autosummarization although R1 will not.
C . Since R2 is configured without autosummarization， it will not propagate the 172.30.1.0/24 route.
D . 172.30.0.0/8 and 10.0.0.0/8.
-
Requirements management is the process of （）
A . A、communicating
B . B、collecting
C . C、filing
D . D、documenting
-
To securely transport EIGRP traffic, a network administrator will build VPNs between sites. What is the best method to accomplish the transport of EIGRP traffic?（）
A . IPSec in tunnel mode
B . IPSec in transport mode
C . GRE with IPSec in transport mode
D . GRE with IPSec in tunnel mode
-
Refer to the exhibit. In this network， R1 is configured not to perform autosummarization within EIGRP. What routes will R3 learn from R2 through EIGRP？（）https://assets.asklib.com/images/image2/2018072317583328155.jpg
A . 172.30.1.0/24 and 10.1.2.0/24； EIGRP only performs autosummarization at the edge between two major networks.
B . 172.30.0.0/16 and 10.1.2.0/24； R2 will perform autosummarization， although R1 will not.
C . Since R2 is configured without autosummarization， it will not propagate the 172.30.1.0/24 route.
D . 172.30.0.0/8 and 10.0.0.0/8.
-
EIGRP is being used as the routing protocol on the PassGuide network. Whiletroubleshooting some network connectivity issues，you notice a large number of EIGRP SIA（StuckinActive）messages. What causes these SIA routes（）
A . The neighboring router stops receiving ACK packets from this router.
B . The neighboring router starts receiving route updates from this router.
C . The neighboring router is too busy to answer the query(generally caused by high CPU utilization).
D . The neighboring router is having memory problems and cannot allocate the memory to process the query or build the reply packet.
-
Which two statements about the EIGRP DUAL process are correct?（）
A . An EIGRP route will go active if there are no successors or feasible successors in the EIGRP topology table.
B . An EIGRP route will go passive if there are no successors in the EIGRP topology table.
C . DUAL will trigger an EIGRP query process while placing the flapping routes in the holddown state.
D . A feasible successor in the EIGRP topology table can become the successor only after all the query requests have been replied to.
E . The stuck in active state is caused when the wait for the query replies have timed out.
F . EIGRP queries are sent during the loading state in the EIGRP neighbor establishment process.
-
Router R1 sets a route tag for subnet 10.1.1.0/24 when redistributing from OSPF into EIGRP.Which of the following unit is assigned to the route tag?（）
A . Kilobits/seconD
B . Tens of microseconds
C . Cost
D . Hop count
E . No unit is assigneD
-
When EIGRP is used as the PE-CE routing protocol which of these statements is correct?（）
A . EIGRP can be used only as the PE-CE routing protocol if the PE and CE routers are in the same AS
B . Other EIGRP AS routes are automatically advertised to the CE router and do not require a redistribution configuration command to be configured
C . Unlike other routing protocols that are used between PE and CE routers, EIGRP supports backdoor links
D . Configure of the VPN is only required on the PE router
-
Which two design recommendations are most appropriate when EIGRP is the data center core routing protocol?（）
A . Summarize data center subnets.
B . Use passive interfaces to ensure appropriate adjacencies.
C . Tune the EIGRP timers to enable EIGRP to achieve quicker convergence.
D . Adjust the default bandwidth value to ensure proper bandwidth on all links.
E . Advertise a default summary route into the data center core from the aggregation layer.
-
Which two design recommendations are most appropriate when EIGRP is the data center corerouting protocol？ （）
A . Summarize data center subnets.
B . Use passive interfaces to ensure appropriate adjacencies.
C . Tune the EIGRP timers to enable EIGRP to achieve quicker convergence.
D . Adjust the default bandwidth value to ensure proper bandwidth on all links.
E . Advertise a default summary route into the data center core from the aggregation layer.
-
Which statement about a none zero value for the load metric (k2) for EIGRP is true?（）
A . A change in the load on an interface will cause EIGRP to recalculate the routing metrics and send a corresponding update out to each of its neighbors.
B . EIGRP calculates interface load as a 5 - minute exponentially weighted average that is updated every 5 minutes.
C . EIGRP considers the load of an interface only when sending an update for some other reason.
D . A change in the load on an interface will cause EIGRP to recalculate and update the administrative distance for all routes learne d on that interface.
-
EIGRP performs automatic summarization at network boundaries. What administrative distance is given to these EIGRP summary routes?（）
A . 1
B . 90
C . 95
D . 0
E . 5
F . 170
G . 255
H . None of the other alternatives apply
-
An administrator types in the command router ospf 1 and receives the er ror message: "OSPF process 1 cannot start." (Output is omitted.) What should be done to correctly set up OSPF？（）
A . Ensure that an interface has been configured with an IP address
B . Ensure that IP classless is enabled
C . Ensure that the interfaces can ping their directly connected neighbors
D . Ensure that an interface has been configured with an IP address and is u
-
Which of the following is true regarding the effect of EIGRP queries on the network design？（）
A . EIGRP queries will be the most significant issue with respect to stability and convergence
B . EIGRP queries are not a consideration as long as EIGRP has a feasible successor with a nexthop AD that is greater than the FD of the current successor route
C . EIGRP queries will only increase the convergence time when there are no EIGRP stubsdesigned in the network
-
Refer to the exhibit. In this network，R1 is configured not to perform autosummarization within EIGRP. What routes will R3 learn from R2 through EIGRP？（）https://assets.asklib.com/images/image2/2018072317150093827.jpg
A . 172.30.1.0/24 and 10.1.2.0/24；EIGRP only performs autosummarization at the edge between two major networks
B . 172.30.0.0/16 and 10.1.2.0/24；R2 will perform autosummarization，although R1 will not
C . Since R2 is configured without autosummarization，it will not propagate the 172.30.1.0/24 route
D . 172.30.0.0/8 and 10.0.0.0/8
-
Process OSPF 1 is redistributing routes from process OSPF 2. Which of the following methods may be used to set the metrics of the redistributed routes?（）
A . Let the metrics default.
B . Use each redistributed route's OSPF metric using the redistribute command's metric transparent keywords.
C . Set the metric using the default - metric router subcommand.
D . Redistribution is not allowed between two OSPF p rocesses.
-
Network Security is a continuous process. Which three phases apply to this process?（）
A . Configure
B . Improve
C . Operate
D . Monitor
E . Secure
F . Troubleshooting
-
Routers R1 and R2 are EIGRP neighbors. R1 has been configured with the eigrp stub connected command. Which of the following is true as a result？（）
A . R1 can learn EIGRP routes from R2, but R2 cannot learn EIGRP routes from R1
B . R1 can send IP packets to R2, but R2 cannot send IP packets to R1
C . R2 no longer learns EIGRP routes from R1 for routes not connected to R1
D . R1 no longer replies to R2's Query messages
E . R2n o longer sends to R1 Query message
-
What is the process of shipment？
-
Refer to the exhibit. EIGRP is configured with the default configuration on all routers. Auto summariz ation is enabled on routers R2 and R3, but it is disabled on router R1.Which two EIGRP routes will be seen in the routing table of router R3？（）
<img src='https://img2.soutiyun.com/ask/uploadfile/2019-03-27/c0432bed5e96b27cf201162a3a16be20.png' />
A. 10.0.0.0/8
B. 172.16.10.0/24
C. 172.16.0.0/24
D. 10.10.10.0/24
E. 172.16.0.0/16
F. 10.10.0.0/16
-
Router R1 uses S0/0 to connect via a T/1 to the Frame Relay servicE. Five PVCs terminate on the serial link. Three PVCs (101, 102, and 103) are configured on subinterface S0/0.1, and one each (104 and 105) are on S0/0 .2 and S0/0.3. The configuration shows no configuration related to EIGRP WAN bandwidth control, and the bandwidth command is not configured at all.Which of the following is true about how IOS tries to limit EIGRP‘s use of bandwidth on S0/0？（）
A.R1 limi ts EIGRP to around 250Kbps on DLCI 102
B.R1 limits EIGRP to around 250Kbps on DLCI 104
C.R1 limits EIGRP to around 150Kbps on every DLCI
D.R1 does not limit EIGRP because noWAN bandwidth control has been configured
-
Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0".Whic h of the following is most likely to have caused this output to occur on R1？（）
A. R1 has been configured with an ip default- network 2.0.0.0 command.
B. R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.
C. R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
D. Another router has been configured with an ip default - network 2.0.0.0 command.
E. Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
-
During the redistribution process configured on RTA, some of the EIGRP routes, such as 10.1.1.0/24 and 10.2.2.0/24,are not being redistributed into the OSPF routing domain. Which two items could be a solution to this proble m？（）
<img src='https://img2.soutiyun.com/ask/uploadfile/2019-03-27/1f3bd3d98218e5077df5d514b253c248.jpg' />
A. Change the EIGRP AS number from 100 to1 in the redistribute command.
B. Add the subnets option to the redistribute command.
C. Change the metric - type to2 in the redistribute command.
D. Configure the redistribute command under router eigrp 1 i nstead.
E. Change the metric to an EIGRP compatible metric value (bandwidth, delay, reliability, load, MTUs) in the redistribute command.
-
Refer to the exhibit. EIGRP had converged in AS 1 when the link between router R1 and R2 went down. The console on router R2 generated the following messages:*Mar 20 12:12:06: %DUAL - 5NBRCHANG E: IP - EIGRP 1: Neighbor 10.1.4.3 (Serial0) is down: stuck in active*Mar 20 12:15:23: %DUAL -3- SIA: Route 10.1.1.0/24 stuck - in - active state in IP - EIGRP 1.Cleaning up The network administrator issued the show ip eigrp topology active command on R2 to check the status of the EIGRP network.Which statement best describes the reason for the error messages？（）
<img src='https://img2.soutiyun.com/shangxueba/ask/64335001-64338000/64337716/48ae99ce89919b8ea814d8bd8606dee0.jpg' />
A. Incorrect bandwidth configuration on router R3 prevents R2 from establishing neighbor adjacency.
B. Incorrect bandwidth configuration on router R 5 prevents R2 from establishing neighbor adjacency.
C. Router R3 did not reply to the query about network 10.1.1.0/24 sent by router R2 .
D. Router R5 did not reply to the query about network 10.1.1.0/24 sent by router R2 .
