-
The options on the NFS server using the nfso command have been adjusted. Which of the following tasks are required in order for these changes to survive a system reboot？（）
A . update /etc/rc.nfs
B . issue the chnfs command
C . recycle nfsd
D . unmount and remount the file system
-
To enable the SNMP daemon during system startup， which of the following files should be modified？（）
A . /etc/rc.net
B . /etc/rc.nfs
C . /etc/rc.tcpip
D . /etc/inetd.conf
-
During the implement phase， systems acceptance testing provides which two of the following services for the customer（）
A . It installs， configures， and verifies monitoring tools and processes in accordance with the operations implementation.
B . It verifies that the Cisco Unified Communications solutions is ready for production.
C . It verifies that the Cisco Unified Communications solution meets their business and technical requirements.
D . It executes and verifies the migration plan by migrating network services from an existing state to a future state.
E . It provides automated tools for measuring system performance under load.
-
A patch has been applied to the operating system. After rebooting, the system is hung. Which of the following commands should have been performed to prevent the system from hanging?（）
A . lppchk, bosboot
B . lslpp -l, oslevel
C . installp -C, lppchk
D . bosboot, synclvodm&e
-
After a system has rebooted from a system crash, which of the following commands should be run to find the location of the dump?（）
A . lsvg -l rootvg
B . sysdumpdev -e
C . sysdumpdev -L
D . cd /var/adm/ra
-
During a NIM install, the system stops with the LED code 611.What is the cause of the issue?（）
A . A failure to NFS mount filesystems from the NIM client
B . A failure to NFS mount filesystems from the NIM master
C . A failure to retrieve the tftp client info from the NIM master
D . A failure to retrieve the tftp server info from the NIM master
-
During system boot， the system hangs at LED 0C31. What is the first step the system administrator should take to correct the problem？（）
A . Check system console connections
B . Check system network connections
C . Boot in service mode and change the bootlist
D . Boot from the AIX installation media and mount rootvg filesystem
-
During a NIM install，the system stops with the LED code 611.What is the cause of the issue？（）
A . A failure to NFS mount filesystems from the NIM client
B . A failure to NFS mount filesystems from the NIM master
C . A failure to retrieve the tftp client info from the NIM master
D . A failure to retrieve the tftp server info from the NIM master
-
A graphics card has been added to the system. After rebooting, the system hangs during the login process with a blue screen indicating "CDE please wait". Which of the following procedures should be performed next?（）
A . Reinstall the CDE software
B . Check the name resolution
C . Uncomment the last line in .dtprofile
D . Boot in maintenance mode and perform fsck on file system
-
During reboot， the system hangs with an LED 0554 message that means， "The boot device could not be opened or a read failed." Which of the following recovery procedures should be taken （）
A . Boot in maintenance mode and use fsck to check hd5.
B . Boot in maintenance mode， access the rootvg and check the /etc/inittab for corruption.
C . Boot in maintenance mode， access the rootvg and rebuild the boot image using the bosboot command.
D . Boot in maintenance mode， and reset the root password.
-
After adding a new Ethernet card to a system and rebooting， the system administrator notices the card was not configured. How can the system administrator determine if there were errors during the configuration process for the card？（）
A . Examine the bootlog with the command： alog -o -f /var/adm/ras/bootlog
B . Display the device attributes and errors with the command： lsdev -C -l ent0
C . Examine the AIX errlog for configuration method errors with the command： errpt -a -C ent0
D . Examine the ODM for configuration errors with the command： odmget -q "method_errors" ent0
-
A system administrator has added a new graphics card to the system and rebooted. The system pauses with C31 in the three-digit displays. Which of the following causes could be the reason for the hang?（）
A . All filesets for CDE have not been loaded. Boot into maintenance mode and load them through SMIT.
B . There is a missing device driver, incorrect console configuration, or a serial device plugged into native S1 port.
C . The new graphics adapter card is marked defined, not available. Rum smit cfgmgr (Install/Configure Devices Added After IPL with the INPUT device /directory for software set to none). This will reconfigure all devices by walking the bus.
D . The LED C31 means that there is a corrupted /dev/hd5. Boot into maintenance mode, fsck /dev/hd5 and then issue the bosboot command.
-
A system administrator has filesystems that should not be mounted during system startup. How can the system administrator prevent the /data filesystem from being mounted during subsequent boots？（）
A . mount -no /data
B . chfs -A no /data
C . mount -t nfs /data
D . chfs -a type=nfs /data
-
After the LED display is flashing 888 and the system is rebooted, which of the following commands should be used to gather dump information?（）
A . snap
B . errpt
C . kdb
D . trace
-
A system was rebooted and is taking a long time toreturn. The administrator has logged into the HMC and sees reference code 0c9. What does this mean?（）
A . The system is configuring a device.
B . A system initiated dump has started.
C . The system is varyingon a volume group.
D . The system is running an inbuilt self test.
-
A modem is set up for a remote TTY connection that will become the system console. How should one verify that the console is enabled as the system console after the next reboot？（）
A . lscons -b
B . lscons -d
C . lscons -s
D . swcons /dev/tty0
-
During reboot the system hangs with an LED 0554 message that means， "The boot device could not be opened or a read failed." What recovery procedures should be taken？（）
A . Boot in maintenance and use fsck to check hd5.
B . Boot in maintenance mode， access the rootvg and check the /etc/inittab for corruption.
C . Boot in maintenance mode， access the rootvg and rebuild the boot image using the bosboot command.
D . Boot in maintenance mode， access the rootvg and use the bootlist command to create a valid boot list.
-
Which key should be pressed on an ASCII terminal during the system initialization to force the system to read from the default boot list？（）
A . 1
B . 3
C . 5
D . 9
-
A system administrator would like to set a system to reboot after a crash. What is the best way to do this？（）
A . smit chgsys
B . bosboot
C . smit dump
D . bootlist -r
-
AIX shows the boot order in the following output： hdisk0 hdisk1 blv=hd5 cd0 What will happen when the system administrator reboots the server？（）
A . The server will boot from cd0
B . The server will boot from hdisk0
C . The server will boot into SMS mode
D . The server will boot from hdisk1
-
AIX shows the boot order in the following output.hdisk0 hdisk1 blv=hd5 cd0. What will happen when the system administrator reboots the server?（）
A . The server will boot from cd0
B . The server will boot from hdisk0
C . The server will boot into SMS mode
D . The server will boot from hdisk1
-
A system was rebooted and is taking a long time to return. The administrator has logged into the HMC and sees reference code 0c9. What does this mean（）？
A . The system is configuring a device.
B . A system initiated dump has started.
C . The system is varyingon a volume group.
D . The system is running an inbuilt self test.
-
The operator needs to change the /test filesystem in the testvg volume group so that it mounts automatically following a system reboot. Which of the following commands is correct?（）
A . chvg -a y testvg
B . chfs -A yes /test
C . mount /test -auto=yes
D . chlv -a automount=y testlv
-
AIX shows the boot order in the following output： hdisk0 hdisk1 blv=hd5 cd0 What will happen when the system administrator reboots the server？（）
A . The server will boot from cd0
B . The server will boot from hdisk0.
C . The server will boot into SMS mode
D . The server will boot from hdisk1.
