The welds used to attach stiffeners to a plate are known as().
A . butt welds
B . seam welds
C . fillet welds
D . plate weld
相似题目
-
A system has two configured fibre channel cards, one of which, fsc0, has failed and must be replaced. Which command should an administrator use to remove the card device and attached child devices?()
A . rmdev -Rdl fcs0
B . rmdev -cdl fcs0
C . rmdev -cdl fscsi0
D . rmdev -Rdl fscsi0
-
A customer plans to add high performance shared storage with three servers and using direct attach. Cost is a minor issue compared to performance. Which of the devices meets this requirement?()
A . DS3200
B . EXP3000
C . DS3300
D . DS3400
-
A system has two configured fibre channel cards, one of which, fsc0, has failed and must be replaced. Which command should an administrator use to remove the card device and attached child devices?()
A . rmdev -Rdl fcs0
B . rmdev -cdl fcs0
C . rmdev -cdl fscsi0
D . rmdev -Rdl fscsi0
-
Refer to the exhibit. The company uses EIGRP as the routing protocol. What path will packets take from a host on 192.168.10.192/26 network to a host on the LAN attached to router R1?()https://assets.asklib.com/images/image2/2018072410123247953.jpg
A . The path of the packets will be R3 to R2 to R1.
B . The path of the packets will be R3 to R1 to R2.
C . The path of the packets will be both R3 to R2 to R1 and R3 to R1.
D . The path of the packets will be R3 to R1
-
At sea, we can use()to fix the ship’s position.
A . steering gear
B . Loran
C . rudder indicator
D . log
-
Which command can be used to determine the type of cable attached to the Serial 0/0 interface on a router?()
A . show interfaces serial 0/0
B . show running-config
C . show version
D . show controllers serial 0/0
E . show ip interface
F . show line serial 0/0
-
The welds used to join shell plates in flush construction are known as().
A . butt welds
B . seam welds
C . fillet welds
D . continuous weld
-
Which command can be used to check the system’s hardware and software for the compatibility with Windows 2000 professional.()
A . WINNT /CHECKUPGRADEONLY.
B . WINNT32 /CHECKUPGRADEONLY.
C . Setup / CHECKUPGRADEONLY.
D . Install / CHECKUPGRADEONLY.
-
In tanker trade,the signing by master the documents relating to the use of jetties and berths ()the shipowners thereby to pay for any damage caused to the jetties or berths by the vessel’s using them.
A . ties
B . binds
C . does
D . ha
-
The required fireman’s outfits required for ship’s are not to be used for any other purpose EXCEPT for the().
A . oxygen and explosion meter when it is used for detection of flare gases
B . self-contained breathing apparatus,when used as protection from gas leaking from a refrigeration unit
C . boots and gloves that are made of rubber or electrically non-conductive material,if used when repairing electrical equipment
D . lifeline,if used by personnel entering a compartment which might be deficient of oxyge
-
An AIX LPAR has been reconfigured to use direct-attached disks. What is the best way to fully remove and delete the Virtual IO volumes?()
A . On the AIX LPAR: rmdev -dl hdisk#, rmdev -dl vscsi#
B . On the VIO Server: rmdev -dev rootvg_disk, rmlv rootlv_name
C . On the AIX LPAR: rmdev -dl hdisk#, rmdev -dl vscsi# On the VIO Server: rmdev -dev rootvg_disk, rmlv rootlv_name
D . On the VIO Server: rmdev -dev rootvg_disk, rmlv rootlv_name On the AIX LPAR: rmdev -dl hdisk#, rmdev -dl vscsi#
-
After GPRS attach,SGSN will assign an identity to identify the MS,what’s it?()
A . TMSI
B . P-TMSI
C . TLLI
D . IMSI
-
Instructions to the crew in the use of all the ship’s lifesaving equipment shall be completed().
A . before sailing
B . within one week of sailing
C . in one month and repeated quarterly
D . within any two month period
-
The Company switches are configured to use VTP. What’s true about the VLAN trunking protocol (VTP)?()
A . VTP messages will not be forwarded over nontrunk links.
B . VTP domain names need to be identical. However,case doesn’t matter.
C . A VTP enabled device which receives multiple advertisements will ignore advertisements with higher configuration revision numbers.
D . A device in "transparent" VTP v.1 mode will not forward VTP messages.
E . VTP pruning allows switches to prune VLANs that do not have any active ports associated with them.
-
At sea,we can use()to fix the ship’s position.
A . VHF
B . Steering Gear
C . Rudder Indicator
D . Lora
-
Possibly the most challenging step of the procedure of Filigree Welding is heating to ______ degrees centigrade to firm the metal.
-
The surname MacDonald in Scotland was probably first used to name Donald’s ______.
-
( )is used to facilitate the writer’s numbering and filing of the letters he or she receives.
-
The following can be used to describe water according to Laozi’s philosophy except________.
-
The “sb.+be+adj.” sentence pattern cannot be used to talk about a person’s height.
-
People began to use fake snow and tinsel on the Christmas Tree in 1800's.
A.Y
B.N
C.NG
-
S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology shown in the exhibit. Originally, static routes were configured between these routers to successfully route traffic between the attached networks. What will need to be done in order to use RIPv2 in place of the static routes?()
<img src='https://img2.soutiyun.com/shangxueba/ask/64407001-64410000/64409000/17b75ef15006e963a847746eb8ec9a38.png' />
A.Configure the no ip subnet-zero command on R1, R2, and R3.
B.Dynamic routing protocols such as RIPv2 cannot be used across Frame Relay networks.
C.Configure the S0/0 interface on R1 as two subinterfaces and configure point-to-point links to R2 and R3.
D.Change the 172.16.2.0/25 and 172.16.2.128/25 subnetworks so that at least two bits are borrowed from the last octet.
E.Change the network address configuration to eliminate the discontiguous 172.16.2.0/25 and 172.16.2.128/25 subnetwork.
-
Faraday’s law of electromagnetic induction can be used to explained the following devices work()
A.Generator
B.Transoformer
C.Electromagnetic furnace
D.Microwave Oven
此题为多项选择题。
-
You can use the structure “_______________” to repeat the customer’s questions.
A:Excuse me;
B:Thanks a lot;
C:What you’re saying;
D:Pardon