What must be configured on the network in order for users on the Internet to view web pages  located on Web Server 2?（）

A . Set up the Network Time Protocol server.  B . Install the files needed to run the web-based GUI.  C . Set up routing and IP addressing on the service module and the interface service engine.  D . Configure a session initiation protocol dial peer for connecting calls to the voice mail and Auto Attendant features.

A . must be Cisco Compatible Extensions version 2 B . must be Cisco Compatible Extensions version 3 C . must be Cisco Compatible Extensions version 4 D . must be associated to a Platinum QoS WLAN E . must be associated to an access point on a Cisco WLC with code version 5.0 or newer

A .  Hardware address takeover must be configured. B .  IPAT via IP aliasing is required for EtherChannel. C .  EtherChannel must be defined as a separate network. D .  HACMP does not support the fallover of EtherChannel.

A . VTP mode B . VTP password C . VTP revision number D . VTP pruning E . VTP domain name F . None of the other alternatives apply

A . Each end of the trunk line must be set to IEEE 802.1E encapsulation. B . The VTP management domain name of both switches must be set the same. C . All ports on both the switches must be set as access port. D . One of the two switches must be configured as a VTP server. E . A rollover cable is required to connect the two switches together. F . A router must be used to forward VTP traffic between VLANs.

A . Visually verify the MAC addresses and then telnet to the switches to enter the switchport-port security mac-address command. B . Have end users e-mail their MAC addresses. Telnet to the switch to enter the switchport-port security mac-address command. C . Use the switchport port-security MAC address sticky command on all the switch ports that have end devices connected to them. D . Use show mac-address-table to determine the addresses that are associated with each port and then enter the commands on each switch for MAC address port-security.

A . ip route 0.0.0.0 0.0.0.0 s0/0/0 B . ip route 0.0.0.0 0.0.0.0 209.165.200.226 C . ip route 209.165.200.0 255.255.255.0 192.168.1.250 D . ip route 192.168.1.0 255.255.255.0 209.165.100.250

A . Provide a password for the encryption B . Set up an Oracle wallet for the encryption C . No setup is required as it is a default encryption method D . Both Oracle wallet and password must be set up for the encryptio

A . multiple privilege levels B . usernames and passwords C . aaa new-model command D . secret password for the root user E . HTTP and/or HTTPS server

A . One per blade B . One per VSAN C . One per fabric D . None are required

A .  Provide a password for the encryption B .  Set up an Oracle wallet for the encryption C .  No setup is required as it is a default encryption method D .  Both Oracle wallet and password must be set up for the encryptio

A . network connections B . location views C . access points D . object definitio

A . ip route 0.0.0.0 0.0.0.0 s0/0/0 B . ip route 0.0.0.0 0.0.0.0 209.165.200.226 C . ip route 209.165.200.0 255.255.255.0 192.168.1.250 D . ip route 192.168.1.0 255.255.255.0 209.165.100.250

A . Infrastructure devices to associate only to this SSID B . Enable IP redirection on this SSID C . Set Data Beacon Rate D . Multiple Basic Service Set Identification （BSSID） E . Set infrastructure SSID

A . infrastructure devices to associate only to this ssid B . enable ip redirection on this ssid C . set data beacon rate D . multiple basic service set identification （bssid） E . set infrastructure ssid

A .  algorithm = failover B .  algorithm = round_robin C .  reserve_policy = no_reserve D .  reserve_policy = single_path

A . network connections B . location views C . access points D . object definitio

A .  Nothing，SSA can support a maximum of 8 initiators per loop. B .  The RAID5 implementation on SSA will only support two initiators per loop. C .  SSA can only support four initiators per lop when using the fat write option. D .  The RAID implementation can be used with three initiators only if the fast write cache option is used on all adapters.

A . Enable the IGMP snooping capability and define the IGMP timeout period. B . Set the Ethernet multicast mode to Enabled， enable the IGMP snooping capability， and define the IGMP timeout period. C . Set the multicast monitor function to Enabled， enable the IGMP snooping capability， and define the mandatory data rate to the minimum value supported. D . Set the Ethernet multicast mode to Multicast and define the multicast group address.

A . Provide a password for the encryption B . Set up an Oracle wallet for the encryption C . No setup is required as it is a default encryption method D . Both Oracle wallet and password must be set up for the encryptio

A .  Fibre Channel ports must be configured from the first port in the module. B .  Ethernet ports must be configured from the last port in the module. C .  Fibre Channel ports must be configured from the last port in the module. D .  Ethernet ports must be configured from the first port in the module.

A. The intranet-auth authentication option B. The redirect-portal application service C. The uac-policy application service D. The ipsec-vpn tunnel