-
When configuring cisco secure acs to support wireless eap authentication,which device must be configured as a aaa client?()
A . location appliance
B . controller-based access points
C . wireless clients
D . wireless control system
E . wireless controller
-
Which of these is mandatory when configuring Cisco IOS Firewall? ()
A . Cisco IOS IPS enabled on the untrusted interface
B . NBAR enabled to perform protocol discovery and deep packet inspection
C . a route map to define the trusted outgoing traffic
D . a route map to define the application inspection rules
E . an inbound extended ACL applied to the untrusted interface
-
When deploying IPCC Express 4.0 for the first time, when and where is the licensing of the customer specified? ()
A . during Installation Cluster Setup, in the CRS Installer
B . after installation, during first-time login, in CRS Application Administration
C . after installation, in CRS License Update Utility
D . during Installation Server Setup, in the CRS Installer
-
When implementing OSPFv3, which statement describes the configuration of OSPF areas?()
A . In interface configuration mode, the OSPFv3 area ID combination assigns interfaces to OSPFv3 areas.
B . In router configuration mode, the network wildcard area ID combination assigns networks to OSPFv3 areas.
C . In interface configuration mode, the IPv6 OSPF process area ID combination assigns interfaces to OSPFv3 areas.
D . In router configuration mode, the IPv6 OSPF interface area ID combination assigns interfaces to OSPFv3 areas.
-
When configuring Frame Relay using point-to-point subinterfaces, which of the following must not be configured?()
A . The local DLCI on each subinterface of the Frame Relay.
B . The Frame Relay encapsulation on the physical interface.
C . An IP address on the physical interface.
D . The subinterface type as point-to-point
-
What OSPF command, when configured, will include all interfaces into area 0?()
A . network 0.0.0.0 255.255.255.255 area 0
B . network 0.0.0.0 0.0.0.0 area 0
C . network 255.255.255.255 0.0.0.0 area 0
D . network all-interfaces area 0
-
Which two features are added when upgrading from IPCC Express Standard to Enhanced? ()
A . Agent Routing
B . Historical Reporting
C . Conditional Routing
D . Prioritized Queueing
E . Agent Queueing
-
What types of orders are exempt from using the IPCC Express Configuration and Ordering Tool? ()
A . orders for coresident deployments
B . orders for adding more seats
C . orders for upgrading from standard
D . orders with less than five seats
E . all orders require using the IPCC Express Configuration and Ordering Tool&e
-
When configuring a serial interface on a router, what is the default encapsulation?()
A . atm-dxi
B . frame-relay
C . hdlc
D . lapb
E .
-
How many VLANs on the UCS must be configured when using FCoE?()
A . One per blade
B . One per VSAN
C . One per fabric
D . None are required
-
Which feature is added when upgrading from IPCC Express Enhanced to IPCC Express Premium? ()
A . supervisory recording
B . WrapUp timer
C . sending e-mails
D . keystroke macros
E . text chat &e
-
In IPCC Express 4.0, where is product licensing stored, and how can configured licenses be viewed?()
A . stored in local files, viewed in CRS License Update Utility
B . stored in LDAP, viewed in CRS Application Administration
C . stored in local files, viewed in CRS Application Administration
D . stored in LDAP, viewed in CRS License Update Utility &e
-
When a Cisco router is configured for SSH, it acts as an ()?
A . SSH client
B . SSH proxy
C . SSH server
D . SSH and SSL server
-
When configuring Cisco Secure ACS to support wireless EAP authentication, which device must be configured as a AAA client?()
A . Wireless Control System
B . wireless clients
C . wireless controllers
D . controller-based access points
E . Location Appliance
-
When will a skills-based CSQ that requires a skill competency of four (4) select an IPCC Express agent? ()
A . if the ICD agent is available and has a skill competency of nine (9) in another skill defined in CRS
B . if the ICD agent is available and has a skill competency of one (1) in the required skill for the CSQ
C . if the ICD agent is available and has a skill competency of seven (7) in the required skill for the CSQ
D . if the ICD agent is available and has a skill competency of three (3) in the required skill defined in CRS
-
When configuring private VLANs, which configuration task must you do first?()
A . Configure the private VLAN port parameters.
B . Configure and map the secondary VLAN to the primary VLAN.
C . Disable IGMP snooping.
D . Set the VTP mode to transparent.
-
What should you set the Client Configuration to when configuring the ODBC Data Source for the Database Subsystem?()
A . TCP/IP
B . Multiprotocol
C . Named Pipes
D . NWLink IPX/SPX
-
Which two statements correctly identify factors to consider when Configuring WAN QoS?()
A . Voice Traffic uses Assured Forwarding
B . Voice Signaling traffic uses Assured Forwarding
C . Voice Signaling traffic uses priority queuing
D . Voice Traffic uses priority queuing
E . Voice signaling traffic should use priority queuing with Assured Forwarding
-
Which three IPCCX configuration steps are only available in the IPCC Express Enhanced or Premium edition? ()
A . Create Resource Groups
B . Create Skills
C . Assign Resource Groups and Skills to Agents
D . Create Contact Service Queues
E . Provision Remote Monitoring
F . Provision Agent-based Routing&e
-
When configuring system state conditions with the Cisco SecurityAgent, what is the resulting action when configuring more than one system state condition? ()
A . Any matching state condition will result with the state being triggered
B . Once a state condition ismet, the system ceases searching further conditions and will cause the state condition to trigger
C . All specified state conditions are used as part of the requirements tobe met to for the state to trigger
D . Once the state conditions are met, they become persistent and can only be removed using the Reset feature
-
When configuring SSH, which is the Cisco minimum recommended modulus value?()
A . 2048 bits
B . 1024 bits
C . 256 bits
D . 512 bit
-
When will an "all configuration" backup be imported into the Cisco UCS Manager?()
A . During the initial configuration from the console
B . Once the basic configuration has been applied
C . To restore the configuration on a secondary fabric interconnect
D . To upgrade the firmware on a replacement fabric interconnect
-
What is the maximum number of CSQs that a call should be queued for when configuring IPCC Express?()
A . 15
B . 20
C . 25
D . 30
E . 40
F . 50&e
-
Which does not need to be configured on ZXCTN6100 when performing basic configuration
A.A.UNI interface configuratio
B.B.Static MAC configuratio
C.C.configuratio
D.D.VLAN interface configuratio