-
TestKing.com has a large corporate network that uses multiple routing protocols.Hosts in a portion of the network that uses EIGRP have become unreachable.Which router command will allow you, the network technician, to view the status of these routes?()
A . TestKing# show eigrp entries
B . TestKing# show protocols
C . TestKing# debug eigrp routes
D . TestKing# show ip route eigrp
E . TestKing# show route eigr
-
Which of the following commands is used to observe the current state of the routing table?()
A . route
B . lsattr
C . netstat
D . ifconfig
-
A router simultaneously receives all the following routes in various routing updates. Which of thefollowing routes would end up in the routing table?(Choose all that apply.)()
A . RIP route 10.1.2.0/24
B . EIGRP route 10.1.2.0/24
C . RIP route 10.1.0.0/16
D . OSPF route 10.1.0.0/16
E . RIP route 10.0.0.0/16
F . OSPF route 10.1.2.0/24
-
Part of the routing table of router PG1 is displayed below:
https://assets.asklib.com/images/image2/2018072610131024176.jpg
From analyzing the above command output,what is the administrative distance of the external EIGRP routes()
A . 24
B . 32
C . 90
D . 170
E . 27316
F . None of the other alternatives apply
-
For a router to successfully redistribute routes between OSPF and EIGRP, which of the following are true?()
A . The router must have one routing protocol configured, but configuration for both routing protocols is not necessary
B . The router must hav e at least one working link connected to each routing domain
C . The redistribute command must be configured under EIGRP to send the routes to OSPF
D . The redistribute command should be configured under OSPF to take routes from EIGRP into OSPF
-
Which of the following commands would you use, to configure a default route to any destination NOT found in the routing table?()
A . Router(config)# ip default-route 0.0.0.0 255.255.255.255 s0
B . Router(config)# ip route 0.0.0.0 255.255.255.255 s0
C . Router(config)# ip default-route 0.0.0.0 0.0.0.0 s0
D . Router(config)# ip route 0.0.0.0 0.0.0.0 s0
E . Router(config)# ip route any any e0
-
Your Cisco network currently runs OSPF and you have a need to policy-route some specific traffic,regardless of what the routing table shows. Which one of these options would enable you to policy-route the traffic?()
A . source IP address and the protocol (such as SSL,HTTPS,SSH)
B . the packet Time to Live and the source IP address
C . type of service header and DSCP value
D . destination IP addre
-
Your Cisco network currently runs OSPF and you have a need to policy-route some specific traffic, regardless of what the routing table shows. Which one of these options would enable you to policy-route the traffic?()
A . source IP address and the protocol (such as SSL, HTTPS, SSH)
B . the packet Time to Live and the source IP address
C . type of service header and DSCP value
D . destination IP addre
-
Refer to the exhibit.which address and mask combination a summary of the routes learned by EIGRP?()https://assets.asklib.com/images/image2/2018072408552539657.jpg
A . 192.168.25.0255.255.255.240
B . 192.168.25.16255.255.255.252
C . 192.168.25.0255.255.255.252
D . 192.168.25.28255.255.255.240
E . 192.168.25.16255.255.255.240
-
Process EIGRP 1 is redistributing routes from process OSPF 2. Which two of the following methods may be used to set the metrics of the redistributed routes?()
A . Let the metrics default.
B . Set the metric components using the redistri bute command's metric keyword.
C . Set the metric components using the default - metric router subcommand.
D . Set the integer (composite) metric using the redistribute command's metric keyword.
-
Which tables of EIGRP route information are held in RAM and maintained through the use of hello and update packets? (Choose two.)()
A . neighbor table
B . SPF table
C . RTP table
D . topology table
E . query table
F . DUAL table
-
Which of the following are methods EIGRP uses to initially populate (seed) its EIGRP topology table, before learning topology data from neighbors?()
A . By adding all subnets listed by the show ip route connected command
B . By adding the subnets of working interfaces over which static neighbors have been defined
C . By adding subnets redistributed on the local router from another routing source
D . By adding all subnets listed by the show ip route static command
-
which address range efficiently summarizes the routing table of the addresses for router main?()https://assets.asklib.com/images/image2/2018072314283060593.jpg
A . 172.16.0.0/18
B . 172.16.0.0/16
C . 172.16.0.0/20
D . 172.16.0.0/21
-
Which statements are true about EIGRP successor routes? ()
A . A successor route is used by EIGRP to forward traffic to a destination.
B . Successor routes are saved in the topology table to be used if the primary route fails.
C . Successor routes are flagged as "active" in the routing table.
D . A successor route may be backed up by a feasible successor route.
E . Successor routes are stored in the neighbor table following the discovery process.
-
Router R1 sets a route tag for subnet 10.1.1.0/24 when redistributing from OSPF into EIGRP.Which of the following unit is assigned to the route tag?()
A . Kilobits/seconD
B . Tens of microseconds
C . Cost
D . Hop count
E . No unit is assigneD
-
When EIGRP is used as the PE-CE routing protocol which of these statements is correct?()
A . EIGRP can be used only as the PE-CE routing protocol if the PE and CE routers are in the same AS
B . Other EIGRP AS routes are automatically advertised to the CE router and do not require a redistribution configuration command to be configured
C . Unlike other routing protocols that are used between PE and CE routers, EIGRP supports backdoor links
D . Configure of the VPN is only required on the PE router
-
Which of the following commands should be used to alter the routing table on a running system without affecting the ODM settings?()
A . inetd
B . route
C . cfgmgr
D . chdev
-
Which tables of EIGRP route information are held in RAM and maintained through the use of hello and update packets (Choose two.)()。
A . neighbor table
B . SPF table
C . RTP table
D . topology table
E . query table
F . DUAL table
-
which address range efficiently summarizes the routing table of the addresses for router main?()
A . 172.16.0.0/18
B . 172.16.0.0/16
C . 172.16.0.0/20
D . 172.16.0.0/21
-
After the show ip route command has been entered,the follwing routes are displayed.Which route will not be entered into the routing table of a neighboring router?()
A . R 192.168.8.0/24 [120/1] via 192.168.2.2, 00:00:10, Serial0
B . R 192.168.11.0/24 [120/7] via 192.168.9.1, 00:00:03, Serial1
C . C 192.168.1.0/24 is directly connected, Ethernet 0
D . R 192.168.5.0/24 [120/15] via 192.168.2.2,00:00:10,Serial0
-
Which of the following commands should be used to display a system routing table?()
A . route
B . netstat
C . iptrace
D . traceroute&e
-
Refer to the exhibit. EIGRP is configured with the default configuration on all routers. Auto summariz ation is enabled on routers R2 and R3, but it is disabled on router R1.Which two EIGRP routes will be seen in the routing table of router R3?()
<img src='https://img2.soutiyun.com/ask/uploadfile/2019-03-27/c0432bed5e96b27cf201162a3a16be20.png' />
A. 10.0.0.0/8
B. 172.16.10.0/24
C. 172.16.0.0/24
D. 10.10.10.0/24
E. 172.16.0.0/16
F. 10.10.0.0/16
-
Router R1 lists 4 routes for subnet 10.1.1.0/24 in the output of the show ip eigrp topology all - links command. The variance 200 command is configured, but no other related commands are configured. Which of the following rules are true regarding R1‘s decision of what r outes to add to the IP routing table?Note that RD refers to reported distance and FD to feasible distanc E.()
A. Adds all routes for which the metric is <= 200 * the best metric among all routes
B. Adds all routes because of the ridiculously high variance setting
C. Adds all successor and feasible successor routes
D. Adds all successor and feasible successor routes for which the metric is<=200 * the best metric among all routes
-
During the redistribution process configured on RTA, some of the EIGRP routes, such as 10.1.1.0/24 and 10.2.2.0/24,are not being redistributed into the OSPF routing domain. Which two items could be a solution to this proble m?()
<img src='https://img2.soutiyun.com/ask/uploadfile/2019-03-27/1f3bd3d98218e5077df5d514b253c248.jpg' />
A. Change the EIGRP AS number from 100 to1 in the redistribute command.
B. Add the subnets option to the redistribute command.
C. Change the metric - type to2 in the redistribute command.
D. Configure the redistribute command under router eigrp 1 i nstead.
E. Change the metric to an EIGRP compatible metric value (bandwidth, delay, reliability, load, MTUs) in the redistribute command.