在路由器中使用show interface命令,如果看到的结果是接口状态和线路协议状态者是down,可能的原因是()。
如果执行了show interface serial 0命令而且出现了消息“Serial line is up,line protocol is up”,对于这条消息的正确解释是什么?()
Which line from the output of the show ip interface command indicates a layer 1 problem?()
检查路由器接口好坏使用show interface命令。
在172.17.22.0网络上的用户无法到达位于172.31.5.0网络上的服务器。网络管理员连接到控制台端口,发出show ip route命令,并且能ping服务器。基于在图示显示的show ip route命令拓扑结构的输出,失败的原因是什么?()https://assets.asklib.com/images/image2/2018072316230752528.jpg
Router# show interfaces serial 0/1 命令的输出显示了如下内容: Serial0/1 is down, line protocol is down. 线路协议为 down(关闭)的原因最可能是什么()
TDCS中show interface命令查看路由器接口,如果显示Ethernet0 is up则表示()。
TDCS中show interface命令查看路由器接口,如显示Ethernet 0 is up则表示()。
当你通过show ip interface来查看IP地址时,发现接口VLAN1的状态为down,请问可能造成这种情况的原因是?()
GGSN的端口检查命令是show ip interface brief。()
PTN 设备单站调试中,常用命令show interface brief查询端口三个层面(AdminStatus,PhyStatus,Protocol)下的up/down状态,其中进入相应接口配置模式下,执行shutdown/no shutdown直接影响哪一项的状态?()
查看路由器的ARP表的命令是show ip route。
show interface命令用来查看(),ping命令用来查看(),远程登录的命令是()。
使用“show port-security interface f0/1”命令可查看交换机端口F0/1的安全配置信息。
假设你是学校的网络管理员,你为了能够Telnet到Star-S2126G上进行远程管理,配置交换机的地址。但是当你进行Telnet时却失败了,当你通过show ip interface来查看IP地址时,发现接口VLAN 1的状态为down,请问可能造成这种情况的原因是?()
路由器命令Router>show interface的作用是()?
在PTN设备中,用命令show interface all可以检测到所有接口的状态。()
在路由器上使用()命令查看路由表。A.route printB.show ip routeC.show routing-tableD.display i
Router R1 has the following configuration. Assuming R1‘s F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?()interface f0/0ipv6 address 2345:0:0:8::1/64
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
46、网络管理员已输入如下命令:ip route 192.168.10.64 255.255.255.192 serial0/0/1 网络管理员输入命令 show ip route 后,该路由并未在路由表中。管理员下一步应如何操作?
在ZXCTN设备调试eth接口过程中,我们常用show interface brief命令查询E1口和以太网口是否运转正常,其中,Admin状态的up和down表示 (),Phy状态的up和down表示 (),Prot状态的up和down表示 ()。
【单选题】网络管理员在三层交换机上创建了VLAN 10,并在该VLAN的虚拟接口下配置了IP地址。当使用命令“display ip interface brief”查看接口状态时,发现VLAN 10 接口处于down状态,则通过怎么样的操作来使得VLAN 10状态,则通过怎样的操作来使得VLAN 10 接口恢复正常?
哪两条信息会显示在 show ip interface brief 命令的输出结果中?()