Which command is used to alter the attributes of "log type" defined in the alog configuration database?（）

An administrator needs to determine what the default run level of a system is. Which command would be used（）

A . Isitab init B . telinit -d C . cat/etc/.init.state D . init

Which command is used to configure RMAN to perform a compressed backup for every backup executed？（）

A . BACKUP AS COMPRESSED BACKUPSET DATABASE B . BACKUP AS COMPRESSED COPY OF DATABASE C . CONFIGURE DEVICE TYPE DISK BACKUP TYPE TO COMPRESSED BACKUPSET D . CONFIGURE DEVICE TYPE DISK BACKUP TYPE COMPRESS E . BACKUP DATABASE COMPRESS

查看答案

Which of the following commands is used to restore the VIO server from a backup image？（）

A . dd B . tar C . restore D . installio

查看答案

which command is used to enable CHAP authentication whit PAP as the fallback method on a serial interface?（）

A . (config-if)#authentication ppp chap fallback ppp B . (config-if)#authentication ppp chap pap C . (config-if)#ppp authentication chap pap D . (config-if)#ppp authentication chap fallback

查看答案

Which of the following commands should be used to determine whether a logical volume is contiguous across a disk？（）

A . lslv B . lsfs C . lspv D . fileplace

查看答案

The nice value is 60 in the ps listing. Which command is used to change this to a value of 20？（）

A . renice -n -20 {PID} B . renice -n 20 {PID} C . renice -n -40 {PID} D . renice -n 40 {PID}

查看答案

Which of the following commands should be used to determine if a remote print queue is down?（）

A . lsqdev B . lpstat C . lptest D . prtconf

查看答案

Which of the following kdb commands is used to obtain a stack trace from a dump? （）

A . trb B . his C . f D . trace

查看答案

Which of the following commands should be used to check whether a system dump is valid and readable?（）

A . kdb B . snap -d C . dbx -vmcore D . od /dev/sysdumpdev

查看答案

Which command is used to display the placement and direction of an IP access control list on a router?（）

A . show access-list B . show ip route C . show ip interface D . show interface E . show interface list F . show ip interface brief

查看答案

On the Catalyst 6500 Series switch, which command is used to establish a console connection to the Firewall Services Module?（）

A . ssh B . connect C . login D . sessio

查看答案

Which Cisco IOS command is used to troubleshoot a problem in which a BGP session stays in the active state?（）

A . debug ip bgp updates B . debug ip tcp events C . debug ip bgp transactions D . debug ip tcp transactio

查看答案

Which command is used to configure a default route?（）

A . ip route 172.16.1.0 255.255.255.0 0.0.0.0 B . ip route 172.16.1.0 255.255.255.0 172.16.2.1 C . ip route 0.0.0.0 255.255.255.0 172.16.2.1 D . ip route 0.0.0.0 0.0.0.0 172.16.2.1

查看答案

Which of the following commands is used to determine the route that the IP packets take to a network host?（）

A . route B . netstat C . iptrace D . traceroute

查看答案

Which command is used to begin a tablespace point-in-time recovery？（）

A . Restore tablespace B . Recover tablespace C . Tablespace recover D . Recover to time E . recover datafile

查看答案

Which of the following is the correct command to document a Power Systems server using sysplan?（）

A . mksysp -m Server-9117-MMA-SN10FC123 > Server-9117-MMA-SN10FC123.sysplan B . mksysplan -f Server-9117-MMA-SN10FC123.sysplan -m Server-9117-MMA-SN10FC123 C . sysplan -new Server-9117-MMA-SN10FC123.sysplan -m Server-9117-MMA-SN10FC123 D . sysplancreate -m Server-9117-MMA-SN10FC123.sysplan -f Server-9117-MMA-SN10FC123

查看答案

Which set of commands is recommended to prevent the use of a hub in the access layer?（）

A . switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security maximum 1 B . switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security mac-address 1 C . switch(config-if)#switchport mode access switch(config-if)#switchport port-security maximum 1 D . switch(config-if)#switchport mode access switch(config-if)#switchport port-security mac-address 1

查看答案

Which of the following commands can be used to determine if a disk drive is causing a bottleneck?（）

A . vmstat B . fileplace C . iostat D . lvmstat

查看答案

Which of the following is the correct command to document a Power Systems server using sysplan（）？

A . mksysp -m Server-9117-MMA-SN10FC123 > Server-9117-MMA-SN10FC123.sysplan B . mksysplan -f Server-9117-MMA-SN10FC123.sysplan -m Server-9117-MMA-SN10FC123 C . sysplan -new Server-9117-MMA-SN10FC123.sysplan -m Server-9117-MMA-SN10FC123 D . sysplancreate -m Server-9117-MMA-SN10FC123.sysplan -f Server-9117-MMA-SN10FC123

查看答案

Which command is used to determine if a host has logged in to the Fibre Channel fabric？（）

A . show flogi database B . show system fc login C . show npv flogi-table D . show npv fcns database E . show interface vfc X flogi F . show interface flogi

查看答案

Which command is used to initialize and configure a NIM master？（）

A . /usr/sbin/nim_init B . /usr/bin/installnim C . /usr/sbin/nimconfig D . /usr/sbin/setup_server

查看答案

Which CLI command is used to create a W3C log？（）

A . make log B . log config C . w3c log config D . advance dproxy config E . mklog file

查看答案

Which of the following commands should be used to determine which disk of a system is experiencing a disk I/O performance problem？（）

A . filemon B . istat C . vmstat D . iostat

查看答案

Which RMAN command is used to verify the status of a backup or copy， and also updates the repository when files have been deleted using operating system commands？（）

A . CHANGE B . RESYNC C . CATALOG D . CROSSCHECK

查看答案

Which command is used to define a combined report？（)

A．SDRSI B．SDRCI C．SDCRI

查看答案

Which command is used to alter the attributes of "log type" defined in the alog configuration database?（）

相似题目

推荐题目